Search Results

37 - 48 of 104 Products for '1 Mhz Repetition Rate' Page 4 of 9 |

1 Mhz Repetition Rate

COHR HyperRapidNX DS 0618 1.pdf

COHR HyperRapidNX DS 0618 1.pdf

…pulse repetition rate).
5 Single-pulse operation (burst number = 1).
6 At 500 kHz.
7 Over 8 hours, ±1°C ambient temperature.
8 With 5 pulses in the burst, at the lowest burst mode operation range frequency.
9 (Pulse repetition rate) x (number of burst) cannot exceed 5 MHz.

COHR Axon DS 0320.pdf

COHR Axon DS 0320.pdf

…Axon 1064 Axon 1064 TPC
Wavelength1 (nm) 920 1064
Average Power (mW) 1000 800 1000 800
Pulse Duration2 (fs) <150
Repetition Rate (MHz) 80 ±1
Beam Mode M2 < 1.3
Beam Asymmetry3,4 0.8-1.2
Beam Diameter 4 (mm) 1.2 ±0.2
Astigmatism (%) <25
Power…

COHR Fidelity-2 DS 0618 4.pdf

COHR Fidelity-2 DS 0618 4.pdf


Ratio of Measured to Transform Limited Pulse Duration <1.2
Peak Power (kW) >450
RMS Noise2 (%) <1
Power Stability3 (%) ±0.5
Repetition Rate (MHz) (factory set) 70 ±2
M2 (average of X&Y) <1.2
Beam Diameter4 (mm) 1.2 ±0.2
Beam Divergence (mrad)…

COHR ChameleonDiscoveryNX DS 0520 1.pdf

COHR ChameleonDiscoveryNX DS 0520 1.pdf

…Duration1,2 (fs) 100
Repetition Rate (MHz) 80 ±0.5
Beam Mode1 M2 <1.2
Beam Diameter1 (mm) 1.2 ±0.2
Ellipticity1 0.8 to 1.2
Astigmatism1 (%) <20
Polarization Linear, Horizontal
Noise1,3 (%) <0.5
Power Stability4 (%) ±1
Tuning Speed5 (nm/s) >50…

COHR Monaco517 DS 0318 4.pdf

COHR Monaco517 DS 0318 4.pdf

1 MHz) 40 (at 500 kHz) 40 (at 750 kHz)
Repetition Rate Single-shot to maximum repetition at maximum energy (defined above)
Pulsewidth (fs) <350
Tuning Range Custom pulse width range may optimized at factory
Spatial Mode TEM00, M2 <1.2
Beam Divergence (mrad, 2q) <1

COHR HyperRapid100 355-SW DS 0716 6.pdf

COHR HyperRapid100 355-SW DS 0716 6.pdf

…Advantages: · 1064 nm, 532 nm and 355 nm outputs · High energy at high repetition rates up to 1 MHz · Pulse on demand trigger with <20 ns jitter · Pulse to pulse energy modulation · 20 ns-burst mode capability for increased ablation rate · High throughput at significantly reduced TCO HyperRapid 100…

COHR HyperRapidNXT DS 0220 1.pdf

COHR HyperRapidNXT DS 0220 1.pdf

1).
5 Maximum power with variable attenuator and process shutter at maximum transmission.
6 Over 8 hours, ±1°C ambient temperature.
7 With 5 pulses in the burst, at the lowest burst mode operation range frequency.
8 (Pulse repetition rate) x (number of burst) cannot exceed 5 MHz.

Laser Focus World - February 2018

Laser Focus World - February 2018

…(Nd:YVO
4
)
gain medium. This laser has an average
power of 7 W, a pulsewidth <15 ps, and a
maximum pulse repetition rate of 1 MHz.
Figure 2 shows typical marks created on
1.4301 stainless steel with this laser. While
these marks appear similar to the…

HYPERRAPID100 DS 0414 5.pdf

HYPERRAPID100 DS 0414 5.pdf

…Advantages: · High throughput at significantly reduced TCO · High energy at high repetition rates up to 1 MHz · Pulse on demand trigger with <100 ns jitter · 20 ns-burst mode capability for increased ablation rate · 1064 nm or 532 nm version · AOM process shutter · Efficient micromachining in…

COHR RegA DS 0217 1.pdf

COHR RegA DS 0217 1.pdf

…from 10 Hz to 10 MHz.
8 Power drift over two hours (after 30 min. warm-up); crystal temperature is controlled with supplied chiller, room temperature stable <±1°C.
9 <1.3 with optional external stretcher/compressor.
Repetition Rate (kHz)
0
1.0
2.0
3.0…

COHR ChameleonMPX DS 1118 1.pdf

COHR ChameleonMPX DS 1118 1.pdf

…(mm) 2
Beam Divergence (mrad) (typical) 0.7
Polarization Horizontal
Repetition Rate (MHz) 80 (locked to pump laser)
Dimensions (L x W x H) 520 x 369 x 158 mm (20.5 x 14.5 x 6.2 in.)
1 Tuning range depends on Pump Wavelength.
2 At maximum of pump and OPO signal tuning…

COHR Axon DS 0719 8.pdf

COHR Axon DS 0719 8.pdf

…Axon 1064 Axon 1064 TPC
Wavelength1 (nm) 920 1064
Average Power (mW) 1000 800 1000 800
Pulse Duration2 (fs) <150
Repetition Rate (MHz) 80 ±1
Beam Mode M2 < 1.3
Beam Asymmetry3,4 0.8-1.2
Beam Diameter 4 (mm) 1.2 ±0.2
Astigmatism (%) <25
Power…