1 - 10 of 205 Search Results for 266 laser
|
|
|
1.
Continuous-Wave (CW)
|
|
10W, and wavelengths in the infrared, visible and ultraviolet are available."> Continuous-Wave (CW) Solid-State Diode-Pumped Laser Systems Output power from 10 mW to >10W, with wavelengths in the IR, visible and UV. Superior Reliability & Performance Lasers and Laser-based Systems Laser ...
Related Searches: 532nm cw laser | 355 nm cw | cube 405 | 266nm cw laser
|
|
|
|
3.
Avia_266_Preinstallation
(PAGE 20 OF 38)
|
|
|
AVIA 266 Laser Preinstallation Manual 14 EXTERNAL COMPUTER CONTROL AVIA Computer Interface This section provides information on interfacing the AVIA 266 laser to an external computer through the RS-232 connector on the rear of the power supply. The RS-232 interface is based on a set of laser control ...
|
|
|
|
|
4.
Continuous-Wave (CW)
|
|
10W, and wavelengths in the infrared, visible and ultraviolet are available."> Continuous-Wave (CW) Solid-State Diode-Pumped Laser Systems Output power from 10 mW to >10W, with wavelengths in the IR, visible and UV. DPSS lasers enable the following applications: Ultrafast pumping Ti:Sapphire ...
Related Searches: 405nm laser | 405nm | compass | 488 laser
|
|
|
|
|
5.
Avia_266_Preinstallation
(PAGE 8 OF 38)
|
|
AVIA 266 Laser Preinstallation Manual 2 An external interlock circuit can be connected to the laser system and wired to a door switch or access panel to provide additional operating safety. When the door is opened, the laser will shut down. The fault must be cleared and the diodes turned on to restart ...
Related Searches: water chiller
|
|
|
|
|
6.
Avia_266_Preinstallation
(PAGE 30 OF 38)
|
|
|
AVIA 266 Laser Preinstallation Manual 24 PRINT FAULT HISTORY ?FH Returns a list of number codes (see ?F) of all faults that have occurred since the last EXIT SCREEN command, separated by an &, or return "System OK" if no latched faults. The EXIT SCREEN command or the EXIT button on the ...
|
|
|
|
|
7.
Avia_266_Preinstallation
(PAGE 4 OF 38)
|
|
|
AVIA 266 Laser Operator's Manual iv LIST OF TABLES 1. Utility Requirements. 5 2. Environmental Requirements . 5 3. Dimensions and Weights . 5 4. EXTERNAL INTERLOCK/CHILLER Connector Pinouts . 10 5. EXTERNAL INTERFACE Connector Pinouts. 11 6. BNC Connectors . 12 7. Suggested Mating Connectors to Interface ...
|
|
|
|
|
8.
Avia_266_Preinstallation
(PAGE 6 OF 38)
|
|
|
AVIA 266 Laser Operator's Manual vi Symbols Used in This Manual and on the Laser System This symbol is intended to alert the operator to the danger of exposure to hazardous visible laser radiation. This symbol is intended to emphasize the presence of important operating instructions.
|
|
|
|
|
9.
Avia_266_Preinstallation
(PAGE 28 OF 38)
|
|
|
AVIA 266 Laser Preinstallation Manual 22 PRINT DIODE1 HOURS ?D1H Returns the number of operating hours on laser diode 1. PRINT DIODE1 OPTIMIZE ?D1O Returns the status of the diode 1 optimization power routine. 1 means the system is optimizing. PRINT DIODE1 PHOTOCELL ?D1PC Returns a voltage that is ...
|
|
|
|
|
10.
Avia_266_Preinstallation
(PAGE 12 OF 38)
|
|
|
AVIA 266 Laser Preinstallation Manual 6 Table 1. Utility Requirements PARAMETER REQUIREMENT AC Voltage Requirements 100 to 240 VAC[1], 47-63 Hz Maximum Current 10 Amps @ 115 VAC 5 Amps @ 230 VAC Cooling: Laser head: Power supply: Conductive to baseplate Air cooled with ambient air Note: All specifications ...
|
|
Coherent Contact Information