Search Results

Refine
1 - 12 of 27 Products for '4 Axis Mount' Page 1 of 3 |

4 Axis Mount

ModeMaster PC M-Squared

ModeMaster PC M-Squared

…Software Description ModeMaster PC Scan Head, Mount, Control / Interface Console and Software for UV, Low-Divergence beams ModeMaster PC Scan Head, Mount, Control / Interface Console and Software for UV, High-Divergence beams ModeMaster PC Scan Head, Mount, Control / Interface Console and Software…

SPIE DSS 2013 Final submitted 4-25-2013x

SPIE DSS 2013 Final submitted 4-25-2013x

…We also demonstrated wavelength-tunability of this stack in the range of 280pm (or 140GHz) at a slight penalty
to the spectral bandwidth.
4. 780NM, WAVELENGTH-LOCKED, 3-BAR STACK PERFORMANCE
4.1 Product Description
To demonstrate power scaling capability with wavelength-locking,…

COHR OBIS CellX DS 0719 4.pdf

COHR OBIS CellX DS 0719 4.pdf

…the objective assembly - see drawing.
3 Measured from nominal beam axis. Adjustment using tilt/yaw adjustment internal to CellX, while meeting all optical specifications.
4 Assumes the objective assembly mounted within less than 200 mm (optical path length) from the output face of CellX.…

book.book

book.book

axis
· X-axis translation, up to 6 mm
· Tilt about the X-axis up to 7 degrees
The Multi-Axis mount provides multiple mounting options that conform to a footprint
for either a StingRay/BioRay standard or Separate Drive. This mount also allows for
more general mounting using…

Microsoft Word - VHG-FAC Paper 07-01-05 .doc

Microsoft Word - VHG-FAC Paper 07-01-05 .doc

…optical axis (off axis) will not
receive feedback from VHG
emitter on optical axis
emitter off optical axis
FAC
VHG
Fig. 4 Feedback situation for the two-piece configuration of FAC and VHG in the case of an array with "smile". The emitter
above the optical axis

COHR StingRayAccessories DS 0818 3a.pdf

COHR StingRayAccessories DS 0818 3a.pdf

…about the laser's mechanical axis
· Tilt about the x-axis up to seven degrees
The StingRay Multi-Axis Mount provides multiple mounting options for the
user, conforming to the standard StingRay/OBIS footprint. It also allows for
more general mounting with two machined slots for…

COHR StingRayAccessories DS 1118 5.pdf

COHR StingRayAccessories DS 1118 5.pdf

…about the laser's mechanical axis
· Tilt about the x-axis up to seven degrees
The StingRay Multi-Axis Mount provides multiple mounting options for the
user, conforming to the standard StingRay/OBIS footprint. It also allows for
more general mounting with two machined slots for…

Chameleon Reliability Antarctia Final WP.pdf

Chameleon Reliability Antarctia Final WP.pdf

…I (408) 764-4983 4
induced misalignments in a statistically large number of
optical mounts of a type used in prototype versions of
Chameleon. In the case of the original mount, although
most of the mounts showed only very small shifts in the
x and y axis angular positions…

Coherent StingRay Laser Safety and Installation Quick Start Guide

Coherent StingRay Laser Safety and Installation Quick Start Guide


4 Turn the key to the ON position.
The laser will begin emitting in
5 seconds (CDRH safety delay).
Mounting
Correctly mounting the laser diode for heat dissipation is
critical to laser lifetime and performance. Any laser
more than 20 mW should be mounted to supply…

Microsoft Word - ECL pw2009.doc

Microsoft Word - ECL pw2009.doc


degrees from the optical axis. When the diode was turned on, the laser diode array was wavelength locked thus
confirming the self-alignment feature. Fig. 4 shows the result.
The VHG was incrementally rotated from 0.8 degree (from normal to the optical axis) to 3 degrees. The spectrum…

Mode Master White Paper July 2011 final.pdf

Mode Master White Paper July 2011 final.pdf

…focusing lens assembly,
dual axis knife edge scanners and a detector. The knife
edges provide the beam diameter data, while the pinholes
provide an intensity profile by which the ModeMaster is
aligned. This head is mounted on a five axis precision
positioner.
Note,…

Mode-Master-Whitepaper FORMFIRST.pdf

Mode-Master-Whitepaper FORMFIRST.pdf

…focusing lens assembly,
dual axis knife edge scanners and a detector. The knife
edges provide the beam diameter data, while the pinholes
provide an intensity profile by which the ModeMaster is
aligned. This head is mounted on a five axis precision
positioner.
Note,…