Search Results

1 - 12 of 33 Products for '50 Watt' Page 1 of 3 |

50 Watt

Ultrashort Pulse Laser Products

Ultrashort Pulse Laser Products

…lasers consists of a 50 W and 100 W models offered at 1064 nm and 1000 kHz for high throughput applications in ps-laser micromachining. HyperRapid NX and NXT Series HyperRapid NX and NXT Series This industrial picosecond laser features high average power operation at >100 Watt across a wide range of…

HYPER RAPID Lasers

HYPER RAPID Lasers

…applications that weren’t previously economically feasible are now possible. Datasheet Hyper Rapid 100 Datasheet Hyper Rapid 50 Datasheet Hyper Rapid 100 355-SW Drawing HR 50 Mechanical Drawing Drawing HR 100 Mechanical Drawing Applications Application Process Material Glass Cutting & Drilling…

MATRIX Family of Q-Switch Lasers

MATRIX Family of Q-Switch Lasers

…& Benefits Power Wavelength 355 nm 532 nm 1064 nm 1 Watt M1; MATRIX 355-YAG MATRIX1064-LP 2 Watt MATRIX 355-1-60; MATRIX 355-1, 5-150 8 Watt MATRIX 355-5-50; MATRIX 355-8-50 MATRIX 532-7-30; MATRIX 532-8-100 MATRIX 1064-7-10 14 Watt MATRIX 532-14-40 MATRIX 1064-10-30 Key benefits for your…

Picosecond Lasers

Picosecond Lasers

…lasers consists of a 50 W and 100 W models offered at 1064 nm and 1000 kHz for high throughput applications in ps-laser micromachining. HyperRapid NX and NXT Series HyperRapid NX and NXT Series This industrial picosecond laser features high average power operation at >100 Watt across a wide range of…

COHR HyperRapid50 DS 0716 4.pdf

COHR HyperRapid50 DS 0716 4.pdf

…HYPER RAPID 50 is a powerful industrial ps-laser offering pulse-on-demand and burst mode operation at output powers up to 50W for high quality micromachining at high throughput.With this laser, the total cost per watt ratio for ps-laser pulses is significantly reduced. The HYPER RAPID 50 provides…

COHR DIAMOND C-30 DS 0817 1.pdf

COHR DIAMOND C-30 DS 0817 1.pdf

…TO
DIRECT OR SCATTERED RADIATION.
CLASS IV LASER RADIATION PRODUCT
PER EN60825-1 (1994)
CO2 LASER 9.2 - 10.8 MICRONS
50 WATT CW
Beam Output
Beam
Output
27.18 ±0.51 mm
(1.07 ±0.02 in.)
29.1 ±0.51 mm
(1.15 ±0.02 in.)
102.2 mm

COHR DIAMOND C-40 DS 1117 1.pdf

COHR DIAMOND C-40 DS 1117 1.pdf

…TO
DIRECT OR SCATTERED RADIATION.
CLASS IV LASER RADIATION PRODUCT
PER EN60825-1 (1994)
CO2 LASER 9.2 - 10.8 MICRONS
50 WATT CW
20.6 mm
(0.8 in.)
30 mm
(1.2 in.)
Max.
37.9 mm
(1.5 in.)
38.1 mm
(1.5 in.)
30.5 mm
(1.2…

COHR DIAMOND C 30 C 30 DS 0619 3.pdf

COHR DIAMOND C 30 C 30 DS 0619 3.pdf

…TO
DIRECT OR SCATTERED RADIATION.
CLASS IV LASER RADIATION PRODUCT
PER EN60825-1 (1994)
CO2 LASER 9.2 - 10.8 MICRONS
50 WATT CW
40.6 mm
(1.60 in.)
40.0 mm
(1.57 in.)
8.0 mm
(0.31 in.)
20.0 mm
(0.79 in.)
102.6 mm
(4.04…

COHR DIAMOND C-20 DS 0817 1.pdf

COHR DIAMOND C-20 DS 0817 1.pdf

…TO
DIRECT OR SCATTERED RADIATION.
CLASS IV LASER RADIATION PRODUCT
PER EN60825-1 (1994)
CO2 LASER 9.2 - 10.8 MICRONS
50 WATT CW
83.7 mm (3.3 in.)
92.5 mm (3.6 in.)
40.6 mm
(1.6 in.)
7.9 mm
(0.3 in.)
14.2 mm
(0.6 in.)
64 mm…

whitepaper next gen mpe v3.pdf

whitepaper next gen mpe v3.pdf

…MOPA that
delivers up to 40 watts at a fixed 1,035 nm wavelength with adjustable repetition rate from
single shot to 50 MHz. The Opera-F is a new type of OPA that incorporates both a non-collinear
stage to enable pulsewidths as short as 50 fs, and a collinear stage that ensures…

LabMax-Pro PC Software Installation and Quick Start Guide

LabMax-Pro PC Software Installation and Quick Start Guide

LabMax-Pro PC Software Installation and Quick Start Guide
18
10. [Trigger tab] Enter
a Level setting in
Watts that represents
a level approximately 50% between zero and the peak power you expect each
pulse to have. If you do not know peak power, enter a Level

Helios Whitepaper2014.pdf

Helios Whitepaper2014.pdf

…1 Watt at a repetition rate of 50 kHz,
due to the small gain crystal. A master oscillator power
amplifier (MOPA) arrangement is therefore used to
reach a higher final output power. The use of a similarly
miniaturized single amplifier stage provides 2.5 W of
average power (50