Search Results

25 - 36 of 53 Products for 'Ar Laser' Page 3 of 5 |

Ar Laser

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…gas supply is directed to both the laser system and
the beam delivery system, make certain the supply and supply line
are properly sized to provide an adequate flow rate to the laser
system.
NOTICE!
Other inert gases such as argon (Ar) must not be used. Use of
inert…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…gas supply is directed to both the laser system and
the beam delivery system, make certain the supply and supply line
are properly sized to provide an adequate flow rate to the laser
system.
NOTICE!
Other inert gases such as argon (Ar) must not be used. Use of
inert…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Operator's Manual
3 - 12
NOTICE!
Other inert gases such as argon (Ar) must not be used. Use of
inert gases will result in damage to the RF power module and
associated matching network components. Only nitrogen or
compressed air as described…

Self-Aligned Non-Dispersive External Cavity Tunable Laser.pdf

Self-Aligned Non-Dispersive External Cavity Tunable Laser.pdf

…analyzer with 10 pm resolution. The linewidth was not measured. The diode laser is
an off-the-shelf 80 mW single mode Fabry-Perot laser with standard facet coating (>10%).
The lens is a 3.6 mm focal length AR coated radial gradient index lens. The side mode
suppression ratio…

Microsoft Word - VHG-FAC Paper 07-01-05 .doc

Microsoft Word - VHG-FAC Paper 07-01-05 .doc

…spectrum of the diode laser is
broader than typically measured with standard arrays due to the AR coating of the diode laser chip. Using the VHGFAC the spectrum is narrowed below 0.5 nm and stabilized over the whole power range.
Fig. 6 Spectrum of diode laser array for various driving…

Sample manuscript showing specifications and style

Sample manuscript showing specifications and style

…grating is respectively 2 and 4 degrees. The laser diode (EagleYard, EYE-RWE-840) has a front facet
AR coating <0.1% reflectivity. The flat mirror in fig. 4(a) reflects both diffracted beams. The two laser frequencies are
competing in the laser cavity. Fig. 4(c) shows an instance of the…

Microsoft Word - 115-80042-001 OPTICAL FEEDBACK WARNING.doc

Microsoft Word - 115-80042-001 OPTICAL FEEDBACK WARNING.doc

…into the laser. · Beware of focusing the light output on a highly reflective/scattering surface. This is another means of generating high optical feedback to the diode. · If fiber coupling, anti-reflective (AR) coated tips are recommended for multimode (MM) fiber. Angle polished tips and AR coating…

SPIE DSS 2013 Final submitted 4-25-2013x

SPIE DSS 2013 Final submitted 4-25-2013x

…x 27mm x 1.8mm.
2.1 Laser bars at 780 nm for Rb laser pumping
Diode laser bars, with a tensile-strained quantum-wells (TM polarized), comprised of 19 emitters, with 90µm emitter
width on 500µm pitch (18% fill-factor), 3mm resonator length, and standard AR coating were mounted on…

Ultra-narrow-band-Tunable-Laserline-Notch-Filter-1.pdf

Ultra-narrow-band-Tunable-Laserline-Notch-Filter-1.pdf

…stack transmit greater than 80% of the incident light
outside the notch. The first and last VHG facets are without
anti-reflection (AR) coatings. An additional 8% transmission could be gained by adding an AR coating to the outside
facet of the first and last VHG in the stack.

Ultra Narrow-Band Tunable Laserline Notch Filter.pdf

Ultra Narrow-Band Tunable Laserline Notch Filter.pdf

…stack transmit greater than 80% of the incident light
outside the notch. The first and last VHG facets are without
anti-reflection (AR) coatings. An additional 8% transmission could be gained by adding an AR coating to the outside
facet of the first and last VHG in the stack.

Microsoft Word - 115-80041-001 Round Module Manual.doc

Microsoft Word - 115-80041-001 Round Module Manual.doc

…to avoid direct feedback into the laser.
· Beware of focusing the light output on a highly reflective/scattering surface. This is another
means of generating high optical feedback to the diode.
· If fiber coupling, anti-reflective (AR) coated tips are recommended for multimode…

ModeMaster PC User Manual

ModeMaster PC User Manual

…reflection zone in the UV-visible
range, and the -2 coating centers the minimum reflection zone in the
visible-near IR range. Single-layer AR coatings have the property
that outside of their operating bandwidth they become "absentee,"
that is, the surface reflectivity merely…