Search Results

37 - 48 of 55 Products for 'Ar Laser' Page 4 of 5 |

Ar Laser

Microsoft Word - 115-80041-001 Round Module Manual.doc

Microsoft Word - 115-80041-001 Round Module Manual.doc

…to avoid direct feedback into the laser.
· Beware of focusing the light output on a highly reflective/scattering surface. This is another
means of generating high optical feedback to the diode.
· If fiber coupling, anti-reflective (AR) coated tips are recommended for multimode…

ModeMaster PC User Manual

ModeMaster PC User Manual

…reflection zone in the UV-visible
range, and the -2 coating centers the minimum reflection zone in the
visible-near IR range. Single-layer AR coatings have the property
that outside of their operating bandwidth they become "absentee,"
that is, the surface reflectivity merely…

Microsoft Word - ECL pw2009.doc

Microsoft Word - ECL pw2009.doc

…out with a high power laser diode array from
Spectra Physics (a division of Newport Corporation). The laser diode array has 19 emitters of width 100 um, 4% front
facet AR coating and output 25 W of optical power at 40 A. Fig. 3 (a) shows a picture of the laser diode bar with the

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…shared purge gas supply is directed to both the laser system and
the beam delivery system, make certain the supply and supply line
is properly sized to provide an adequate flow rate to the laser system.
Other inert gases such as argon (Ar) must not be used. Use of
inert gases…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

laser system and
the beam delivery system, make certain the supply and supply line
is properly sized to provide an adequate flow rate to the laser system.
NOTICE!
Other inert gases such as argon (Ar) must not be used. Use of
inert gases will result in damage to the RF laser

00 E-250 Pre.book

00 E-250 Pre.book

…gas supply is directed to both the laser system and
the beam delivery system, make certain the supply and supply line
are properly sized to provide an adequate flow rate to the laser
system.
NOTICE!
Other inert gases such as argon (Ar) must not be used. Use of
inert…

Coherent Optoskand Brochure 10-20-17.pdf

Coherent Optoskand Brochure 10-20-17.pdf

…5
The unsurpassed performances of the Optoskand
high-power fiber optic cables make them the
number one choice for most industrial lasers on
the market. Thanks to a well developed technology
featuring quartz block, mode stripper and internal
water cooling, the fibers can…

Coherent Whitepaper - Astrella Tisch Sphere FINAL.pdf

Coherent Whitepaper - Astrella Tisch Sphere FINAL.pdf

…interaction
length at a high intensity. This established approach is proven to allow the generation of highpower (up to 5 mJ), few-cycle laser pulses at kHz repetition rates.
A differentially pumped hollow fiber was used here. As pioneered by Tisch and others,
differential pumping…

Quotation KML QGYYMMDD G  Institute Contact

Quotation KML QGYYMMDD G Institute Contact

…Walnut Street, Suite 102, Boulder CO 80301 www.kmlabs.com 303-544-9068
5
important to note that the full
output of the Astrella® laser is not
needed for EUV generation, so that
a good portion of the pulse energy
can be reserved for other purposes,
such as pumping…

Biosafety Level 3 setup for multiphoton microscopy in vivo

Biosafety Level 3 setup for multiphoton microscopy in vivo

…the laser head BSC. For convenience, the laser head BSC can be placed on a rail
installed at the top of the power supply BSC, allowing their movement as unit within the BSL3 laboratory. The
laser head BSC was built with an opening in the front panel for exhaust air and exit for the laser

MerMAIDs: a family of metagenomically discovered marine anion-conducting and intensely desensitizing channelrhodopsins

MerMAIDs: a family of metagenomically discovered marine anion-conducting and intensely desensitizing channelrhodopsins

…mode and
splitting of the interferogram).
RR spectroscopy. RR spectra were acquired with excitation lines of an Ar+ (514
nm, 488 nm) and Kr+ laser (413 nm) (Coherent, Santa Clara CA). Raman signals
were detected in a backscattering configuration (180°) using a confocal…

PL-501 Book.book

PL-501 Book.book

PL-501 Laser Operator's Manual
A-6
Summary of Precautions
· Review the objects in front of the laser and note which surfaces are a possible
hazard for back reflections. Change the objects to be less reflective whenever
possible. Adding Anti-Reflective (AR) coatings to optics…