Search Results

1 - 12 of 24 Products for 'Assist Gas' Page 1 of 2 |

Assist Gas

MetaBEAM1000c Pre.book

MetaBEAM1000c Pre.book

gas should be used in place of Nitrogen to purge the
laser of the LMT system. Using other gases may result in a fire.
Assist Gas
Option System
There is another assist gas input for the customer to use other assist
gasses besides nitrogen, such as CDA or oxygen. The assist

COHR META10C DS 1017 4.pdf

COHR META10C DS 1017 4.pdf

…operating cost sealed CO2 laser for cutting metal and non-metal · Auto focus and capacitive height sensing · High flow/pressure adjustable coaxial assist gas jet · Gull wing, dual access doors with removable pallet, front and rear pass through OPTIONS · Machine Vision · Pallet Automation · Nesting…

00 M5C Pre Install.book

00 M5C Pre Install.book

Utility Requirements and Installation
3 - 29
Figure 3-17. Utilities Panel
A
Assist Gas
Input
Exhaust
Sensor
Input
Outlet to
Chiller
Regulator
Vent
Laser Purge
Gas Input
Control Air
Input
Inlet from
Chiller

00 LMT Pre.book

00 LMT Pre.book

…CUST.
INITIALS
Fire Bed / Plenum Review proper cutting bed and plenum
cleaning / maintenance procedures.
Assist Gas Recommend Inert Gases for assist gas
(e.g., Nitrogen or Argon)
Material Review materials which will be cut.
Fire Extinguisher Fire extinguisher must…

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

…Assembly Removal
3. Set the nozzle assembly on the table and remove the gas assist tubing. Take care to not touch the optic window with
your fingers. See Figure 3.
Figure 3. Nozzle Assembly - Remove Assist Gas Tube
4. Once the nozzle assembly is completely removed you need to…

Microsoft Word - 2018 11 Whitepaper CleanWeld E

Microsoft Word - 2018 11 Whitepaper CleanWeld E

…the intensity distribution of the focused laser spot to introducing beam motion
(wobble), to other factors like the precise dynamics of assist gas delivery or vapor evacuation.
The CleanWeld integrated approach addresses all these areas.
Figure 1: Schematics of key hole and melt…

CMM 11.1.indd

CMM 11.1.indd

…or flat
stock material with micron level precision
and tolerance. Processing can be carried
out with high-pressure co-axial assist
gas to help remove ablation debris when
cutting thick walled materials and with
inner diameter (ID) water flow, where
water is passed…

Industrial Laser Solutions - May/June 2015

Industrial Laser Solutions - May/June 2015


Laser micro-cutting is a non-contact, cost-effective process if heat accumulation from the laser and the mechanical force from a process assist gas can
be controlled. For economic effciency, it
is necessary to perform the process free
of burr or debris so that post-processing…

META-Advanced-Laser-Case-Study-Laser-Cutting-Tool-Increases-Throughput.pdf

META-Advanced-Laser-Case-Study-Laser-Cutting-Tool-Increases-Throughput.pdf

…also inherently more economical to operate
than a higher power laser system. One major reason
for this is that they use much less assist gas than the
company's bigger system. They also use far less
electricity. This turned out to be an important factor,
because it allowed…

Laser-Cutting-Tool-Increases-Throughput-at-Advanced-Laser-Waterjet-Cutting.pdf

Laser-Cutting-Tool-Increases-Throughput-at-Advanced-Laser-Waterjet-Cutting.pdf

…also inherently more economical to operate
than a higher power laser system. One major reason
for this is that they use much less assist gas than the
company's bigger system. They also use far less
electricity. This turned out to be an important factor,
because it allowed…

Coherent LaserCutters 1.pdf

Coherent LaserCutters 1.pdf

…fully hardened steel sheets can be cut with ease, using the same parameters as employed for annealed material. META machines also incorporate an assist gas delivery system, making it easy to take full advantage of their processing characteristics. For example, nitrogen cutting yields excellent edge…

Intersign CaseStudy.pdf

Intersign CaseStudy.pdf

…Coherent META Platform
The Coherent META Laser Machining Center integrates a CO
2
laser, CNC controller, beam delivery system, assist gas delivery system, drive system and laser cutting head all into one
compact machine frame with a standard table size of 4 feet by
4 feet…

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions