Search Results

Refine
1 - 12 of 16 Products for 'Baud Rate' Page 1 of 2 |

Baud Rate

Avia preinstall.book

Avia preinstall.book


Baud Rate
The baud rate of the 9-pin RS-232 port can be changed by means of
the BAUDRATE=NNN command described in Table 11. After the
baud rate is changed, the new setting will be used until it is changed
(even if the system power is switched off).
To set the baud rate

EnergyMax-USB/RS User Manual

EnergyMax-USB/RS User Manual

…section.
Baud Rate
Selects the transmit and receive baud rates together when the device
has an RS-232 serial host port. The command has no effect when the
device has a USB host port. The query returns the currently selected
baud rate.
Command:…

EnergyMax-RS Sensors

EnergyMax-RS Sensors

…applications
* Fast 14-bit A/D converter and FPGA processor for high speed, accurate operation
* RS-232 sensors operate up to 1 kHz maximum available baud rate
* Synchronized dual unit operation to support A/B ratiometry
* State-of-the-art EnergyMax Sensor Technology Contact Us About This Product…

EnergyMax-USB/RS Software Installation and Quick Start Guide

EnergyMax-USB/RS Software Installation and Quick Start Guide


5. (EnergyMax-RS sensors only)
Click Add a RS-232/Serial Port on
the Setting dropdown menu.
6. (EnergyMax-RS sensors only) On
the Add Serial Sensor menu,
select the Com Port and Baud
Rate parameters and then click the
OK button.
Blue
LED

PowerMax-USB-RS UserManualAddendum V00-76-02 .fm

PowerMax-USB-RS UserManualAddendum V00-76-02 .fm

…Manual (part number 1169780). The PowerMax-RS sensors communicate over an RS-232 port using the RS-232 settings shown below. RS-232 Port Settings Baud rate: 9600 Data bits: 8 Parity: None Stop bits: 1 Flow control: None Questions? Call: (USA) 1.800.343.4912 (Europe) +49-6071-968-0 (International)…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

…5-second CDRH delay 5-5
SYST:CDRH? Queries CDRH delay state 5-5
SYST:COMM:BAUD Sets serial communication baud rate 5-6
SYST:COMM:BAUD? Queries serial communication baud rate 5-6
SYST:COMM:HAND Enables/disables SCPI handshaking 5-6
SYST:COMM:HAND? Queries SCPI handshaking…

LabMax-Pro SSIM User Manual

LabMax-Pro SSIM User Manual

…Data Flow Control No software or hardware flow control methods for serial communication is used.
Baud Rate and Other
Communication
Settings
The host must use a fixed baud rate setting of 115200, 8-bit,
1-stop bit, no-parity. Refer to the following table:
Using the USB…

LabMax UserManualAddendum V00-63-41 .fm

LabMax UserManualAddendum V00-63-41 .fm

…settings and has the following format: "B,P,D,S"
where B is the baud rate, P is the parity, D is the number of data bits,
and S is the number of stop bits. The default value is "19200,N,8,1".
· Valid baud rates are: 9600, 19200(default), 38400, 57600, and
115200.
· Valid…

book.book

book.book

…status of the CDRH laser emission
delay
5-6
SYST:COMM:BAUD Sets the serial communication baud rate
5-6
SYST:COMM:BAUD? Queries the serial communication baud rate
SYST:COMM:HAND Toggles system SCPI handshaking
5-6
SYST:COMM:HAND? Queries system SCPI handshaking…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…95
Diameter (mm) 19.05
Material Black annodized AL 6061 T1
Commands Description
CDRH Enables/Disables CDRH Delay
BAUD Set Baud Rate
HAND Enables/Disables SCPI Handshaking
HOUR Reports System Lasing Hours
MOD Reports Laser Model
PNUM Reports Part Number…

Microsoft Word - 115-80040-001 Compact Laser Module Manual.doc

Microsoft Word - 115-80040-001 Compact Laser Module Manual.doc

…through RS232. All RS232 commands are
available after laser system auto start.
4.4.1 Baud rates and serial port settings
Each controller is shipped from the factory with a fixed 9600 baud, which cannot be changed.
The other serial port parameters are: 8 data bits, 1 stop bit and…

GUI 3.88 Revision History.pdf

GUI 3.88 Revision History.pdf

…Allow Export tool to export to Excel in German
Resolves AVIA NX:#1022 - Increase mutex timeout when reading ?HELP over RS232 with
low baud rates
Resolves AVIA NX:#1003 - Release and reacquire LOCKOUT when switching from one
connection mode to another (e.g. RS232 to USB)