Search Results

Refine

Result Type

1 - 12 of 16 Products for 'Beam View Camera' Page 1 of 2 |

Beam View Camera

LaserCam-HR II User Manual

LaserCam-HR II User Manual

…(this page)
· Mounting the camera (p. 3-3)
Software
Installation
Refer to the BeamView-USB Software Installation Guide
(1186747)--included on the CD that shipped with your
product--for complete software installation instructions. To view
that document online:

Microsoft Word - Understand Different Laser Beam  Rev 1 Final.doc

Microsoft Word - Understand Different Laser Beam Rev 1 Final.doc

…measure extremely
small beams.
Power (or Energy) of the Beam
The power or energy of the beam is another important point that
can influence the choice of beam profiling technology. In general,
beam analyzers are too sensitive to view laser beams directly,
which is…

Microsoft Word - inspect-online - A Flexible Approach - 2016-02-02

Microsoft Word - inspect-online - A Flexible Approach - 2016-02-02

…architecture is the single straight line
projection geometry. Here, simple optics fan out the laser beam so that it forms a straight line of
illumination on the part. When viewed by a camera from an angle different from the projector, the line is
distorted by the surface of the part -…

QFS 50 2017.pdf

QFS 50 2017.pdf

…kHz
Pulse duration 150 - 200 ns
Operation mode Q-switched / pulsed
Output power 50 W
Long-term stability ± 1 %
Red aiming beam < 0.2 mW
Optical fiber cable 4.7 m, non-detachable
Minimal bending radius 100 mm
Processing head FLBK 46-90/60 or 44-60/60 or…

COHERENT LMC 2016-2017 Catalog .pdf

COHERENT LMC 2016-2017 Catalog .pdf

…and fixed attenuation for beams up to
2000W/cm2 or 50J/cm2
· C-Mount threads couple directly to cameras
Attenuation Optics and Accessories
Most cameras are too sensitive for direct viewing of
laser beams. For example, a typical diagnostics camera
saturates at only ~0.5…

COHR WP  OPSL Invariant Beam Properties final 5.3.18.pdf

COHR WP OPSL Invariant Beam Properties final 5.3.18.pdf

…recombines
these reflected beams in a configuration called a Mach-Zehnder interferometer. The recombined
beam is then expanded and viewed using a CCD camera.
If the OPSL chip remains flat with no thermal lensing, then the image at the camera would be
uniform across its…

CaseStudy TIRF MullinsLab UCSF.pdf

CaseStudy TIRF MullinsLab UCSF.pdf

…switch wavelengths between alternate camera frames,
so that we build up pseudo-simultaneous (interleaved)
videos at two or even three laser wavelengths. And we
need to do this switching with no undesirable dead time
or shifts in the beam path, i.e., without using
mechanical…

Bio Photonics - September 2015

Bio Photonics - September 2015

…wavelengths between alternate camera
frames to build up pseudosimultaneous (i.e., interleaved) videos at two or
sometimes three laser wavelengths.
This switching must be performed with
no undesirable dead time (i.e., shifts
in the beam path) and without using
mechanical…

LIT BioPhotonics OBIS-GALAXY TIRF-Microscopy 0915.pdf

LIT BioPhotonics OBIS-GALAXY TIRF-Microscopy 0915.pdf

…wavelengths between alternate camera
frames to build up pseudosimultaneous (i.e., interleaved) videos at two or
sometimes three laser wavelengths.
This switching must be performed with
no undesirable dead time (i.e., shifts
in the beam path) and without using
mechanical…

COHR LaserCam-HRII DS 0318 2.pdf

COHR LaserCam-HRII DS 0318 2.pdf

…Radiological Health on all systems ordered for shipment after August 2, 1976.
Coherent offers a limited warranty for all LaserCam-HR II Beam Diagnostic Cameras. For full details of this warranty coverage, please refer to the Service section at www.Coherent.com or contact your local Sales

Coherent StingRay Laser Safety and Installation Quick Start Guide

Coherent StingRay Laser Safety and Installation Quick Start Guide

…operator from seeing the beam. Always use caution when wearing safety eyewear. Laser beams can burn volatile substances like alcohol, gasoline, ether and other solvents, and can damage lightsensitive elements in video cameras, photomultipliers, and photodiodes. Reflected beams can cause damage. To…

Photonics Spectra - September 2015

Photonics Spectra - September 2015

…corners are
often required to accommodate buttons,
controls, LEDs and camera lenses. CO
2
lasers are typically limited to cutting glass
in straight lines because their round output
beam must be reshaped into a long, thin
line in order to distribute the intense heat…