Search Results

1 - 12 of 202 Products for 'Beam Width' Page 1 of 17 |

Beam Width

HELIOS

HELIOS

…Single-shot to 125 kHz Set Point for Guaranteed Specifications 50 kHz 125 kHz 50 kHz 125 kHz Pulse Width (FWHM) <0.79 ns <0.69 ns <0.95 ns <0.69 ns <0.85 ns Spatial Mode TEM 00 (M 2 < 1.25) Beam Diameter (Gaussian Fit, 1/e2) 3.5 mm 2.5 mm 2 mm Polarization Linear Jitter (between sequential pulses,…

Astrella Ultrafast Ti:Sapphire Amplifier

Astrella Ultrafast Ti:Sapphire Amplifier

…up to >7 mJ pulse energy at 1 kHz, 800 nm at either 5 mJ or >7 mJ, 1 kHz
* Pulse Width Ultrafast Ti:Sapphire Amplifier - Astrella is specified to provide up to >7 mJ pulse energy at 1 kHz, 800 nm at either 5 mJ or >7 mJ, 1 kHz Pulse Width <35 fs or <100 fs Stability <0.5% rms Beam quality M2 <1.25

DIAMOND C-Series

DIAMOND C-Series

…≤200 ns pulse widths. The C-55 and C-70 lasers, are specified at 55W and 70W output, respectively, and are available as either air-cooled or water-cooled units, and both have the same dimensions. The C-70 is available in both elliptical and circular beam versions. Height and width is the same on…

DIAMOND J-3-5 CO Laser - 5µm

DIAMOND J-3-5 CO Laser - 5µm

…CO 2 laser. This enables the production of smaller holes and features, and narrower kerf widths when cutting. Coherent offers CO lasers over a wide range of performance power levels all with high quality beam (M² Fully Sealed Carbon Monoxide Laser - While CO lasers were first developed decades ago,…

BeamMaster USB Knife-Edge Based Beam Profilers

BeamMaster USB Knife-Edge Based Beam Profilers

beam width, and the profile intensity data is autoscaled (optional) to fit the display height. Added detail can be obtained in a special high-resolution mode. This is very useful for analyzing beams that are far from Gaussian in shape or smaller than 100 µm. Beam Position and Ellipticity The beam

YAG/Harmonics and IR Sensors

YAG/Harmonics and IR Sensors

…lasers operating at low repetition rates, such as those based on Nd:YAG, Erbium, Ruby and Ho:YAG. The YAG/Harmonics sensor can operate with laser beams up to 35 mm in diameter, and can work at 1064 nm, 532 nm, 355 nm and 266 nm without the need to change diffusers or any other accessories. The…

UVblade Excimer Laser

UVblade Excimer Laser

…power model) 2000 Repetition Rate (Hz) 200 200 600 600 600 Energy Density (mJ/cm 2) 370 340 330 340/320 (high power model) 315 Beam Length (mm) 250 380 465 750 950 Beam Width (µm) 400 300 400 250/500 (high power model) 400 Homogeneity Long Axis (%, 2 sigma) 1.8 1.8 1.8 1.8 1.8 Steepness Short Axis…

RAPID FX

RAPID FX

…train. Datasheet RAPID FX Drawing RAPID FX Spec Drawing Features & Benefits
* Pulse width 100:1 At 1m from laser output Polarisation Direction Vertical ± 3° Contrast Ratio >100:1 At 1m from laser output Beam Pointing Stability ± 50 µrad/°K Long-term Pointing Stability (over 8 hours) <± 50 µrad…

RegA Family

RegA Family

…diffraction-limited output beam with energy to >6 µJ at the standard 250 kHz repetition rate. Utilizing chirped pulse amplification, the RegA amplifies seed pulses from the Mira or Vitara depending on the final performance requirements. RegA 9000 –Offers pulse widths in the regime of 160fs.…

High Power Laser | HighLight™ FL-1000P Pulsed Fiber Laser

High Power Laser | HighLight™ FL-1000P Pulsed Fiber Laser

…e-service capability. The HighLight FL1000P lasers deliver a maximum pulse energy of 100 mJ, at pulse widths between 10 ns and 100 ns, and with repetition rates ranging from 10 kHz to 30 kHz. A beam parameter product of typical 20 mm x mrad (for a 400 μm, round core output fiber) enables this power…

FLARE NX Short-Pulsed DPSS Lasers

FLARE NX Short-Pulsed DPSS Lasers

…Pulse on demand, repetition rates from single-shot up to 2 kHz
* Excellent beam quality: TEM00/M2 500 >300 >100 Pulse Energy Variation ptp (%) (after 10 sec. over 10 sec.) ±5 Pulse Repetition Rate (Hz) up to 2000 Pulse Width (ns)(FWHM, average over 10 sec.) 1.45±0.2 1.15±0.2 1.0±0.2 Spatial Mode TEM…

PerfoLite Laser Perforation System

PerfoLite Laser Perforation System

…power: 450 - 1,000 watts
* Hole diameters: 50 - 300 microns
* Holes per cm: 5 - 50
* Web speed: 100 - 600 m/min
* Paper width: 25 - 150 mm Features at a glance - Laser power: 450 - 1,000 watts Hole diameters: 50 - 300 microns Holes per cm: 5 - 50 Web speed: 100 - 600 m/min Paper width: 25 - 150 mm