Search Results

1 - 12 of 38 Products for 'Chiller Manual' Page 1 of 4 |

Chiller Manual

00 Laser Cooling.book

00 Laser Cooling.book

…............................................................................v
Symbols Used in This Manual and on the Laser System .................................................v
Introduction…

Revolution High-Power Q-Switched Laser System Preinstallation Manual

Revolution High-Power Q-Switched Laser System Preinstallation Manual

Revolution Laser Preinstallation Manual
3 - 2
Controller AC Voltage 200-240 VAC, 50-60 Hz, 9 A Max
Air-Cooled Chiller AC Voltage
220 VAC (± 10 %), 50 Hz, 12 A Max
OR
220 VAC (± 10 %), 60 Hz, 12 A Max
Water-Cooled Chiller AC Voltage
(Figure 3-1)
220 VAC (±…

Libra PreInstallation.book

Libra PreInstallation.book

Manuals for additional information.
Water Chiller The closed-loop water chiller dissipates the heat generated by the
system and stabilizes the Vitesse, Evolution, and amplifier cavity.
The temperature is optimized in the factory and is typically ~21 °C.
Refer to the chiller

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Paladin Advanced Mode Locked UV Laser Preinstallation Manual
2 - 12
Figure 2-4. Termotek Chiller P307-16273 (for 16W-35W Systems)
483
190,5
259,4
499
99

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

…Operator's Manuals for additional information.
Water Chiller The closed-loop water chiller dissipates the heat generated by the
system and stabilizes the Vitara, Revolution, and amplifier cavity.
The temperature is set to 20 °C and should not be changed. Refer to
the chiller

Picosecond laser

Picosecond laser

…to close and
the laser diodes to deactivate (powering-off). The power supply and the chiller remain active. In case the Interlock is being
closed again, the laser diodes remain turned off. A manual
switch (off and on) is not necessary. When an active circuit is
connected the…

Verdi preinstall.book

Verdi preinstall.book

…fault protection.
4. Proceed to the paragraph titled, "Installing the Chiller".
Installing the
Chiller
Install and setup the chiller in accordance with the user's manual
furnished with the chiller
Final Installation
and Initial
Turn-On
Procedures

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual Preliminary: December 18, 2015
3 - 10
Chiller Electrical
Disconnect
It is recommended that the chiller have a main power disconnect to
electrically isolate it from mains power for maintenance and service.
Consult a…

Quick Setup.fm

Quick Setup.fm

…Section Five of the Operator's manual.
Copyright© Coherent Inc., 4/99. All rights reserved. P/N: 0175-814-00, Rev. A
Figure 1. Cooling Connection Hardware
Figure 2. Chiller Hardware Installed
Figure 3. Head Hardware Installed
Figure 4. Chiller Controls
ON/OFF

Laser Marking Workstations

Laser Marking Workstations

…standards
* A large laser-safe window allows viewing of the laser process
* Sliding door (LME-RM RT has a hinged door on the side of the unit)
* Manual Z-Axis for focusing laser head
* Work area lighting on all models
* Swing arm for monitor and ergonomic keyboard access
* Stop Marking push button…

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…Operator's Manuals for additional information.
Water Chiller The closed-loop water chiller dissipates the heat generated by the
system and stabilizes the Vitara, Revolution, and amplifier cavity.
The temperature is set to 20 °C and should not be changed. Refer to
the chiller

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Operator's Manual
3 - 10
Chiller Electrical
Disconnect
It is recommended that the chiller have a main power disconnect to
electrically isolate it from mains power for maintenance and service.
Consult a qualified electrician to select and…