Search Results

Refine

Result Type

1 - 12 of 12 Products for 'Connector Rf' Page 1 of 1 |
  • 1

Connector Rf

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.

Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.
Figure 3-17.…

Book.book

Book.book

…system requires a remote computer control box to
initiate digital pulse operation.
The control box BNC connector has an input impedance of
2.2 K ohm. The laser SMB connector has an input impedance of
50 ohm..
1. Connect the laser as shown in "Section Three: Installation"…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…VDC marked connector on the rear panel. This is a
special filtered connector that passes DC current but blocks RF
emission. As illustrated in Figure 3-17, it is important that the user
make this connection using two wrenches to prevent damaging the
connector.
It is critical…

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

…VDC marked connector on the rear panel. This is a
special filtered connector that passes DC current but blocks RF
emission. As illustrated in Figure 3-16, it is important that the user
make this connection using two wrenches to prevent damaging the
connector.
It is critical…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.
Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.
Figure 3-17.…

00 E-250 Pre.book

00 E-250 Pre.book

…VDC marked connector on the rear panel. This is a
special filtered connector that passes DC current but blocks RF
emission. As illustrated in Figure 3-16, it is important that the user
make this connection using two wrenches to prevent damaging the
connector.
It is critical…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…VDC marked connector on the rear panel. This is a
special filtered connector that passes DC current but blocks RF
emission. As illustrated in Figure 3-17, it is important that the user
make this connection using two wrenches to prevent damaging the
connector.
It is critical…

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

…VDC marked connector on the rear panel. This is a
special filtered connector that passes DC current but blocks RF
emission. As illustrated in Figure 3-12, it is important that the user
make this connection using two wrenches to prevent damaging the
connector.
It is critical…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…control connector Connector for a DB25 interconnection cable.
This connector supplies control and input modulation signals from the user to the
RF power module and supplies status information from the laser system.
Embeddedcontrol/diagnostic
interface connector
LAN connector

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…the Connector Cable (Item 9) is connected.
8
48 VDC (+)
(terminal)
Connects +48 VDC from the DC power supply to the RF power supply.
Use a 3/4" wrench. Apply 190 lb.-in. (21.4 N·m) torque to nut supplied.
9
Laser to RFPS
connector cable
Connector cable…

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC

…to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.
Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.
- 48 VDC Cable…

Avia preinstall.book

Avia preinstall.book

AVIA 266 Laser Preinstallation Manual
10
Table 5. EXTERNAL INTERFACE Connector Pinouts
THIS CONNECTOR IS A DB-25 PIN FEMALE (PLUG WITH SOCKETS) CONNECTOR.
PIN DESCRIPTION FUNCTION
1 Analog Ground Analog signal ground reference.
2 Analog Input 1 0 to +5 V. (DO NOT USE)…