Search Results

1 - 12 of 37 Products for 'Continuous Co2 Laser' Page 1 of 4 |

Continuous Co2 Laser

SST 2017-09 Laser Marking.pdf

SST 2017-09 Laser Marking.pdf

…Clara, CA
The basics of laser marking are reviewed, as well as current and emerging laser technologies.
Laser marking is established at multiple points
in semiconductor production and applications
continue to diversify. There are several laser
technologies servicing the…

DIAMOND C-20 and C-30 Air-Cooled OEM Lasers Preinstallation Manual, Rev. AE

DIAMOND C-20 and C-30 Air-Cooled OEM Lasers Preinstallation Manual, Rev. AE

…environmental
requirements, and limitations.
C-20 and C-30 lasers are sealed-off, RF-excited CO2
lasers, capable of
continuous wave (CW) or modulated operation. From the laser safety
point of view, these lasers are considered to be components and must be
integrated into…

DIAMOND C-20 and C-30 Liquid-Cooled OEM Lasers Preinstallation Manual, Rev. AF

DIAMOND C-20 and C-30 Liquid-Cooled OEM Lasers Preinstallation Manual, Rev. AF

…environmental
requirements, and limitations.
C-20 and C-30 lasers are sealed-off, RF-excited CO2
lasers, capable of
continuous wave (CW) or modulated operation. From the laser safety
point of view, these lasers are considered to be components and must be
integrated into…

Coherent-new-lasers-improve-glass-cutting-methods wp.pdf

Coherent-new-lasers-improve-glass-cutting-methods wp.pdf

…than 4 µm.
Laser Scribe and Break - Photothermal Process
Another well-established glass cutting process is called laser scribing (or laser scribe and break)
and uses carbon dioxide (CO2
) lasers with continuous wave output in the mid-infrared. CO2
laser
scribing can…

Industrial Laser Solutions - May/June 2015

Industrial Laser Solutions - May/June 2015

…CO laser offers high-power, 5-6µm output Carbon monoxide (CO) laser technology was developed in the mid-1960s at the same time as CO 2 lasers. The CO laser was attractive because it had the potential to be 2x more effcient than CO 2 lasers. However, the CO laser presented challenges: Early CO lasers

Laser Focus World - February 2018

Laser Focus World - February 2018


Picosecond laser marking
With picosecond lasers, the pulse duration
is typically shorter than the time for heat to
flow out of the laser interaction zone, even
in metals, so peripheral thermal effects
are greatly reduced compared to nanosecond lasers. This means that a…

00 M5C Pre Install.book

00 M5C Pre Install.book

…a pulsed or continuous
mode, the infrared CO2
laser beam is invisible to the human eye.
Optical radiation in the CO2
laser wavelength range is absorbed by
the cornea. As a result, corneal burns are a likely result if the eye is
exposed to a CO2
laser beam. Severe…

Industrial Laser Solutions - January / February 2014

Industrial Laser Solutions - January / February 2014

…line scan or the
step-and-repeat method (FIGURE 2).
In the line scan method, the laser beam
is shaped into a line (that is, a very high
aspect ratio rectangle) and then swept continuously across the surface to be cleaned.
The number of pulses to which a given spot
on…

Lasers | Photonics Handbook®

Lasers | Photonics Handbook®

…name suggests, continuous-wave lasers produce a continuous, uninterrupted beam of light, ideally with a very stable output power. The exact
wavelength(s) or line(s) at which this occurs is determined by the characteristics of the laser medium. For example, CO2
molecules readily lase at…

CO Lasers from Lab to Fab

CO Lasers from Lab to Fab

…monoxide (CO) and carbon dioxide (CO 2 ) lasers are similar technologies that took two different paths of development. CO 2 lasers are deployed extensively in a wide range of industrial applications, and their use continues to grow. In contrast, CO lasers were largely restricted to laboratory…

32311a coverSinglesRR.indd

32311a coverSinglesRR.indd

…low to medium power CO2
, solid state and semiconductor lasers used in industrial
materials processing is very diverse. New product introductions such as our Diamond J-series CO2
and
CO lasers continue to support our growth in this area. These lasers represent a cost-effective…

34706a cover.indd

34706a cover.indd

…low to medium power CO2
, solid state and semiconductor lasers used in industrial
materials processing is very diverse. New product introductions such as our Diamond J-series CO2
and
CO lasers continue to support our growth in this area. These lasers represent a cost-effective…