Search Results

1 - 12 of 29 Products for 'Cooling Chiller' Page 1 of 3 |

Cooling Chiller

Laser Marking Workstations

Laser Marking Workstations

…module (oscillating table configuration only)
* Digital readout, motorized or programmable upgrade of Z-Axis
* Refrigerated recirculating water chiller for all LME-RM versions (laser dependent)
* Automated Pick ‘N Place parts handling
* Custom Motion Control ability
* Fume extractor, available for…

00 Laser Cooling.book

00 Laser Cooling.book

…systems, designed to match the operating requirements of
ion lasers. Details are given in Appendix A: Coherent Cooling
Options.
Closed-Loop
Chiller
Chillers have many of the same advantages of heat exchangers
insofar as a fixed volume of water is recirculated through…

Verdi preinstall.book

Verdi preinstall.book

…switch shall be clearly marked as the disconnecting device for the laser, and shall be
within easy reach of the operator.
LASER HEAD AIR COOLED
POWER SUPPLY
UMBILICAL
FACILITY
POWER
WATER LINES (if using Water Cooling)
CHILLER FACILITY
POWER

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…Supply 3 m (10 ft.) 3 m (10 ft.)
Revolution Chiller 2.4 m (8 ft.) 3 m (10 ft.)
Vitara-S Power Supply
Vitara-S Controller
3 m (10 ft.) 3 m (10 ft.)
SDG Elite 3 m (10 ft.) N/A
1. The requirement needs to be met only if the water cooled chiller option is purchased.

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…temperature cooling fluid. Because the
properties of the cooling fluid are important for laser performance,
ensure that the conditions remain within the tolerance limits listed in
Table 1-2 on page 1-8 (operator's manual) at all times.
A closed-loop cooling system (chiller)

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

cooling system (chiller) should be used to obtain
consistent and stable laser performance. The chiller must be able to
remove up to 8.5 kW of heat, plus an additional 2 kW if the
liquid-cooled DC power supply option is used. The coolant composition for the closed-loop chiller is…

Paladin Advanced Preinstallation.book

Paladin Advanced Preinstallation.book

…2-4
Water Cooling ............................................................................................................ 2-4
Chiller ........................................................................................................................…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…of the Chiller Line Voltage for Paladin 8W/10W ............................. 3-6
Selection of the Chiller Line Voltage for Paladin 16/24/35 W ......................... 3-8
Cooling System.................................................................................................…

00 LMT Pre.book

00 LMT Pre.book

…planning recommendations.
Liquid Cooling
System
The LMC system requires an external, closed loop water cooling
system. This can be satisfied by a commercially available chiller, or
an existing cooling system. Coherent does not supply chillers, but
can recommend a model…

00 E-250 Pre.book

00 E-250 Pre.book


loops as long as they do not reduce the required flow to the laser, or
they may be cooled by a separate chiller.
Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should
always be above the dew point to prevent condensation from developing inside…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB


loops as long as they do not reduce the required flow to the laser, or
they may be cooled by a separate chiller.
Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should
always be above the dew point to prevent condensation from developing inside…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA


loops as long as they do not reduce the required flow to the laser, or
they may be cooled by a separate chiller.
Coolant Temperature At the laser head, the inlet temperature of the cooling fluid should
always be above the dew point to prevent condensation from developing inside…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions