Search Results

Refine

Result Type

1 - 12 of 14 Products for 'Diamond K Manual' Page 1 of 2 |

Diamond K Manual

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual
4 - 10
Output Signal
Recommendation
There are five output signals from the Real Time I/O Interface
Connector. Four of these indicate the status of the laser system.
These four outputs (duty cycle limit, VSWR limit,…

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

…0.1 F
1
7
9
15
4
EN
EN GND
13
14
11
10
5
6
16
2
3
1.5 K 2 K
1.5 K 2 K
100
100
LMH6644
LMH6644
AM26C31
REAL TIME I/O INTERFACE
12 8
14
15
16
CONNECTOR

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual
4 - 10
Output Signal
Recommendation
There are five output signals from the Real Time I/O Interface
Connector. Four of these indicate the status of the laser system.
These four outputs (duty cycle limit, VSWR limit,…

DIAMOND C-70 Air-Cooled Laser Preinstallation Manual, Rev. AD

DIAMOND C-70 Air-Cooled Laser Preinstallation Manual, Rev. AD

Diamond C-70TM Air-Cooled Laser Preinstallation Manual
2 - 8
3. TAMPER PROOF LABEL
4. QC APPROVAL LABEL
5. MANUFACTURE DATE LABEL
6. ROHS "20" LABEL
7. VOLTAGE WARNING LABEL
8. WARNING APERTURE LABEL
Figure 2-2. Location of Safety Labels (Sheet 3 of 3)
W…

DIAMOND C-70 Liquid-Cooled Laser Preinstallation Manual, Rev. AD

DIAMOND C-70 Liquid-Cooled Laser Preinstallation Manual, Rev. AD

Diamond C-70TM Liquid-Cooled Laser Preinstallation Manual
2 - 8
1. IDENTIFICATION LABEL
2. DANGER OF LASER RADIATION LABEL
3. TAMPER PROOF LABEL
4. QC APPROVAL LABEL
5. MANUFACTURE DATE LABEL
Figure 2-2. Location of Safety Labels (Sheet 3 of 4)
W A R R A N T Y…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

DIAMOND J-3 Series OEM Lasers Preinstallation Manual
4 - 10
Output Signal
Recommendation
There are five output signals from the Real Time I/O Interface
Connector. Four of these indicate the status of the laser system.
These four outputs (duty cycle limit, VSWR limit,…

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-3-5 Series OEM Lasers Preinstallation Manual
4 - 10
Output Signal
Recommendation
There are five output signals from the Real Time I/O Interface
Connector. Four of these indicate the status of the laser system.
These four outputs (duty cycle limit, VSWR limit,…

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC

DIAMOND J-5 Series OEM Lasers Preinstallation Manual
4 - 10
Output Signal
Recommendation
There are five output signals from the Real Time I/O Interface
Connector. Four of these indicate the status of the laser system.
These four outputs (duty cycle limit, VSWR limit,…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…0.1 F
1
7
9
15
4
EN
EN GND
13
14
11
10
5
6
16
2
3
1.5 K 2 K
1.5 K 2 K
100
100
LMH6644
LMH6644
AM26C31
REAL TIME I/O INTERFACE
12 8
14
15
16
CONNECTOR

DIAMOND C-60+ Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND C-60+ Series OEM Laser Preinstallation Manual
52
4.10 Control Signal Connection
Electrical control of the C-60+ Series lasers is achieved via an RJ-45
connector built into the system. The signals carried on each of the pins
are indicated in Table 4-4. Details about…

DIAMOND C-20 and C-30 Liquid-Cooled OEM Lasers Preinstallation Manual, Rev. AF

DIAMOND C-20 and C-30 Liquid-Cooled OEM Lasers Preinstallation Manual, Rev. AF

…4-2. Signal Interface Description and Connector Pinout
PIN NO. SIGNAL DESCRIPTION
1 Modulation
TTL logic input; 1=RF ON, 0=RF OFF; 1 k impedance
This input turns on the laser. See also Pin 7, Control Enable, below
2 + 15 VDC ± 0.5 VDC, 0.25 Amps Max output for customer use…

DIAMOND C-20 and C-30 Air-Cooled OEM Lasers Preinstallation Manual, Rev. AE

DIAMOND C-20 and C-30 Air-Cooled OEM Lasers Preinstallation Manual, Rev. AE

…interface are discussed in "Laser Operation" in the operator's
manual.
Table 4-1. Signal Interface Description and Connector Pinout
PIN NO. SIGNAL DESCRIPTION
1 Modulation
TTL logic input; 1=RF ON, 0=RF OFF; 1 k impedance
This input turns on the laser. See also Pin 7,…