Search Results

Refine

Result Type

1 - 9 of 9 Products for 'Emission Indicator Fault' Page 1 of 1 |
  • 1

Emission Indicator Fault

Avia preinstall.book

Avia preinstall.book

…no active faults.
Fault codes:
1=Emission Indicator Fault,
2=External Interlock Fault,
3=PS Cover Interlock Fault,
4=SHG Temp. Fault,
5=N/A,
6=Laser Rods Temp. Fault,
7=FHG Temp. Fault,
8=Diode 1 Temp. Fault,
9=Diode 2 Temp. Fault,
10=Baseplate…

00 E-250 Pre.book

00 E-250 Pre.book

…Power Indication
LED
Green emission indicates DC power is on (48 VDC). Located
on Ethernet connector.
Figure 4-1 (above)
Table 4-2. Differences in Real-Time Interface Between K Series OEM and E-250 Series
STATUS OR
CONTROL
K-SERIES OEM E-250
Faults

Book.book

Book.book


Laser Emission
Status
The Laser Emission Status screen indicates the current state of laser
output and system status. The central indicator also shows Standby,
CDRH Delay, and System Faults. The ON and OFF buttons are used
to toggle laser emission.
Laser Mode…

Vitara Preinstall.book

Vitara Preinstall.book

…Laser Radiation
Emission
Indicators
The LASER ON indicators on both the power supply and the laser
head illuminate a few seconds after power is applied to the pump
power supply. The indicators are visible without exposing the operator to laser emission. Amber or white light…

Libra PreInstallation.book

Libra PreInstallation.book


to laser emission while manipulating the controls [CFR
1040.10(f)(7)/EN 60825-1/IEC 60825-1, clause 4.8].
Manual Reset
Mechanism
Following an interlock fault or unexpected loss of electrical power,
laser operation requires manual clearing of the fault condition(s)

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB


manual
Power Indication
LED
Green emission indicates DC power is on (48 VDC). Located
on Ethernet connector.
Figure 4-1 (above)
Electrical Interface Connections
INTERFACE EMBEDDED
DIAGNOSTICS RJ-45 JACK
(GREEN POWER-ON INDICATING LED)
REAL TIME…

Coherent StingRay Laser Safety and Installation Quick Start Guide

Coherent StingRay Laser Safety and Installation Quick Start Guide

LED Indicator and Analog Fault Output Status
For information about fault conditions, refer to the
Coherent StingRay Operator's Manual (1223124).
Multi-State LED
5 Hz flashing
Steady on
Fault
Condition
All other
conditions
Red LED Green LED
Laser…

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf


the laser, a five-second power-on delay, an interlock
RCA jack on the back panel and a laser emission
indicator. (For countries requiring a second laser
emission indicator, a second lamp that connects to
the cable I/O connector can be purchased separately
[part no.…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…diagnostics and status information.
Appendix A:
Embedded Diagnostics
in the operator's
manual
Power Indication
LED
Green emission indicates DC power is on (48 VDC). Located
on Ethernet connector.
Figure 4-1 (above)
EXTENDED I/O CONNECTOR
25…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions