Search Results

Refine

Result Type

1 - 12 of 14 Products for 'External Interlock Fault' Page 1 of 2 |

External Interlock Fault

Verdi preinstall.book

Verdi preinstall.book


7
External
Interlock
The system will not operate with the interlock open. An interlock
connector is located on the power supply rear panel. The interlock
status is monitored by the CPU. If the interlock is open, the message,
"External Interlock Fault" will be…

Avia preinstall.book

Avia preinstall.book

…no active faults.
Fault codes:
1=Emission Indicator Fault,
2=External Interlock Fault,
3=PS Cover Interlock Fault,
4=SHG Temp. Fault,
5=N/A,
6=Laser Rods Temp. Fault,
7=FHG Temp. Fault,
8=Diode 1 Temp. Fault,
9=Diode 2 Temp. Fault,
10=Baseplate…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

…page 2-3.
Interlock Jumper This is a mechanical-style jumper for
CDRH interlock. The interlock has
terminal style connections that permit
connection to an external control
device.
Table 4-1. Coherent BioRay Controller Status LED States
Action Ready Fault On
No…

Vitara Preinstall.book

Vitara Preinstall.book


3 - 7
External
Interlock
An interlock connector is located on the pump laser power supply
rear panel. If the interlock is open, laser emission will terminate, and
the SYSTEM FAULT LED (red) will illuminate. The system ships
with an interlock defeat which is…

Book.book

Book.book

…= External Laser Power Mode
?F = Fault Code Decimal
?FF = Fault Bits Binary
?FL = Fault List
?HH = Hour Counter
?HID = Head ID Value
?INT = Interlock Status
?K = Interlock Status
?LC = Interlock Status
?L = Laser
?LT = Laser Type
?LF = Fault

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…down and the shutter will close. The fault must be cleared and the
diodes turned on to restart the laser.
To incorporate an external safety interlock circuit into the laser
system, turn off the laser and remove the jumper from the interlock
connector on the master power supply…

Paladin Advanced Preinstallation.book

Paladin Advanced Preinstallation.book

…down and the shutter will close. The fault must be cleared and the
diodes turned on to restart the laser.
To incorporate an external safety interlock circuit into the laser
system, turn off the laser and remove the jumper from the interlock
connector on the master power supply…

Libra PreInstallation.book

Libra PreInstallation.book

…Manual
3 - 8
External
Interlock
The use of system interlocks is important to assure safe operation of
the laser system.
An external interlock connector is provided on the SDG Elite rear
panel. In the event of an interlock fault during normal operation,…

book.book

book.book


Interlock Jumper
Figure 6-18 shows the Interlock Jumper on the front panel of the Remote:
This mechanical-style jumper is for CDRH interlock. The interlock has terminal style
connections that permit connection to an external control device.
The 2-position Interlock Connector…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…drives an external interlock loop which can be
opened with electromechanical switches. It should not be driven
directly by a logic IC, unless it is a high-voltage peripheral driver
capable of withstanding 24 V and capable of sinking at least 9 mA.
Over Temperature
Fault

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC

…drives an external interlock loop which can be
opened with electromechanical switches. It should not be driven
directly by a logic IC, unless it is a high-voltage peripheral driver
capable of withstanding 24 V and capable of sinking at least 9 mA.
Over Temperature
Fault

Quick Setup.fm

Quick Setup.fm

…on the Customer Data Sheet (approximately 25°C).
4. Install the External Interlock defeat, or hook the system to an External Interlock circuit. See
Section Six of the Operator's manual for an example external interlock circuit.
5. Plug-in the Vitesse power supply and enable the AC…

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions