Search Results

Refine
25 - 36 of 97 Products for 'Faults' Page 3 of 9 |
Related Categories: 2 Micron | Rf Excited Co2 Laser | Mtbf | J5 | Mod

Faults

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…following fault conditions
· Over temperature
· Circuit malfunction
· Absence of the input modulating signal
· Critical drop of laser diode output power due to aging
Fault output is an open collector of the transistor that allows wire junction OR functionality with fault

UCLD Catalog.book

UCLD Catalog.book

…installation and site requirements, and troubleshooting. Students will learn to identify proper
operation and will be qualified to diagnose faults at the major component level. Beam delivery optics and integration will also be discussed.
Key Topics: Laser and electrical safety; daily…

COHR StingRay BioRay DS 0618 3.pdf

COHR StingRay BioRay DS 0618 3.pdf

…Ground
Fault
Vmod
Vmod Ground
RS-232 Transmit
RS-232 Receive
RS-232 Ground
Red
Black
Green
Blue
Red/Black
Orange
White
White/Black
HR Hirose
R10A-10P-12SC(73)
1000 mm
Vin
Vin Ground
Fault
Vmod…

COHR StingRay BioRay DS 0119 3.pdf

COHR StingRay BioRay DS 0119 3.pdf

…Ground
Fault
Vmod
Vmod Ground
RS-232 Transmit
RS-232 Receive
RS-232 Ground
Red
Black
Green
Blue
Red/Black
Orange
White
White/Black
HR Hirose
R10A-10P-12SC(73)
1000 mm
Vin
Vin Ground
Fault
Vmod…

Discovery ShutDown PowerUp Procedures.pdf

Discovery ShutDown PowerUp Procedures.pdf

2) Expect that the fault light will flash for several minutes. When it stops flashing, turn the key
switch on the power supply (`3' of fig 1.) to `Enable' and allow the laser to thermalise for 1hr
before beginning to realign optics.
Apppendix: Envirommental Storage and Operating…

Coherent StingRay Laser Safety and Installation Quick Start Guide

Coherent StingRay Laser Safety and Installation Quick Start Guide

LED Indicator and Analog Fault Output Status
For information about fault conditions, refer to the
Coherent StingRay Operator's Manual (1223124).
Multi-State LED
5 Hz flashing
Steady on
Fault
Condition
All other
conditions
Red LED Green LED
Laser…

Chameleon Ultra Vision COPO MPX ShutDown PowerUp Procedure.pdf

Chameleon Ultra Vision COPO MPX ShutDown PowerUp Procedure.pdf

…reservoir will
drain into the head. Switch off the chiller using power switch `A' after the fault.
5.) Repeat step 3 to refill the reservoir
6.) Repeat Step 4. If there are further faults, keep following the refilling step while also looking for
leaks.
7.) The MRU and…

Libra PreInstallation.book

Libra PreInstallation.book

…60825-1/IEC 60825-1, clause 4.8].
Manual Reset
Mechanism
Following an interlock fault or unexpected loss of electrical power,
laser operation requires manual clearing of the fault condition(s)
[CFR 1040.10(f)(10)/EN 60825-1/IEC 60825-1, clause 4.11].
Use of controls…

EnergyMax-USB/RS User Manual

EnergyMax-USB/RS User Manual

…-310 is raised when the firmware detects an unexpected or
unrecoverable error. This error condition includes unrecoverable
hardware faults.
Error 100 is raised when the device receives an unrecognized
command or query.
Error 101 is raised when the device receives a command…

Paladin Advanced Preinstallation.book

Paladin Advanced Preinstallation.book


in the area wear laser safety eyewear.
Chiller to Laser Head
Connection (option)
Use a standard RS-232 cable to receive chiller fault alarm messages
from the chiller. Figure 3-16 shows the connections on the back of
the laser head and chiller. Activate the chiller query…

34706a cover.indd

34706a cover.indd

…activities,
manufacturing, our corporate headquarters and other critical business operations are located near
major earthquake faults in Santa Clara, California, an area with a history of seismic events. Any such
loss or detrimental impact to any of our operations, logistics…

32311a coverSinglesRR.indd

32311a coverSinglesRR.indd

…activities,
manufacturing, our corporate headquarters and other critical business operations are located near
major earthquake faults in Santa Clara, California, an area with a history of seismic events. Any such
loss or detrimental impact to any of our operations, logistics…