Search Results

Refine
37 - 46 of 46 Products for 'Fieldmaxii to' Page 4 of 4 |

Fieldmaxii to

COHR ExcimerCatalog2019.pdf

COHR ExcimerCatalog2019.pdf

…PM1KX - -
VYPER 308 FieldMaxII-TO PM1KX - -

* Other Coherent measurement product configurations may be compatible with these lasers. Contact factory for more details.
1 In addition to stand-alone meters, USB sensor models are also available for most of these recommendations.

compatibility matrix 02

compatibility matrix 02

…Lasers 355 to 577 nm FieldMaxII-TO PM10 Sapphire Laser 458 TO 594 nm FieldMaxII-TO PS10 OBIS Lasers 355 to 785 nm FieldMaxII-TO PS10 Verdi Lasers 532 nm FieldMaxII-TO PM10, PM30 Diode Lasers CUBE 375 to 785 nm FieldMaxII-TO PS10 OBIS 355 to 785 nm FieldMaxII-TO PS10 Radius 375 to 635 nm…

2009 LMCCatalog86.pdf

2009 LMCCatalog86.pdf

…Sensor
CUBE 375 to 785 FieldMaxII-TO PS10
Radius 375 to 635 FieldMaxII-TO PS10
All Laser Diode Modules FieldMaxII-TO PS10
FAP 780 to 840 LabMax-TOP LM-150FS + SMA adapter
Duo FAP 785 to 820 LabMax-TOP LM-150FS + SMA adapter
Quattro FAP 790 to 980 LabMax-TOP LM-150FS…

GUI 3.88 Revision History.pdf

GUI 3.88 Revision History.pdf


Caught an exception when the FieldMaxII DLL cannot be found
Upgraded to WiX Setup 3.11.1
Monaco:#1023 - If the PD4 optimizer fails due to a fault then display an error
message on the GUI
AVIA NX:#1053 - Ask production users if they want to optimize TT without changing

FMII-P QuickStartGuideRevAD.fm

FMII-P QuickStartGuideRevAD.fm

…Start Guide FieldMaxII-PTM Laser Energy Meter This guide presents a "mini-tutorial" that explains how to connect a sensor to your FieldMaxII-P meter and begin taking measurements within minutes. For indepth information about the FieldMaxIIP meter, refer to the FieldMaxII-P User Manual (1086242).

2016-Ultrafast-Laser-Systems-Catalog.pdf

2016-Ultrafast-Laser-Systems-Catalog.pdf


2 With large heat sink.
3 The PS10 is recommended when making higher resolution or low power measurements.
4 See above for sensors to measure pump lasers.
Below and on the following page are recommendations for selecting the power and energy
measurement tools for your…

COHR RLScatalog 2017revA web.pdf

COHR RLScatalog 2017revA web.pdf


2 With large heat sink.
3 The PS10 is recommended when making higher resolution or low power measurements.
4 See above for sensors to measure pump lasers.
Below and on the following page are recommendations for selecting the power and energy
measurement tools for your…

COHR OP-2 LM-2 OpticalSensors DS 0719 1.pdf

COHR OP-2 LM-2 OpticalSensors DS 0719 1.pdf

…used with OP-2 VIS, LM-2 VIS, OP-2 IR and LM-2 IR sensors to allow operation
up to 5 W in the visible and 3W in the infrared regions. The attenuator threads into the sensor
in place of the light shield to provide from 1100:1 to 950:1 attenuation. Each attenuator is
calibrated for…

COHR OP-2 LM-2 OpticalSensors DS 1119 2.pdf

COHR OP-2 LM-2 OpticalSensors DS 1119 2.pdf

…used with OP-2 VIS, LM-2 VIS, OP-2 IR and LM-2 IR sensors to allow operation
up to 5 W in the visible and 3W in the infrared regions. The attenuator threads into the sensor
in place of the light shield to provide from 1100:1 to 950:1 attenuation. Each attenuator is
calibrated for…

FMII-TOP QuickStartGuideRevAD.fm

FMII-TOP QuickStartGuideRevAD.fm

…how to set up a pyroelectric sensor to take an energy or average power measurement.
o
Connect a pyroelectric sensor to the
25-pin connector. Note: If your sensor
has a BNC plug, you will need to attach
a 25-pin adapter.n
Press either the Up or
Down arrow to