Search Results

25 - 36 of 57 Products for 'Flat Top Laser' Page 3 of 5 |

Flat Top Laser

Microsoft Word -  w layout cs ohara Mar2015.docx

Microsoft Word - w layout cs ohara Mar2015.docx

…formation of a permanent refractive-index change segment inside glass using femtosecond laser processing. Achieving a new diffraction optical component by forming a refractive-index change segment inside flat glass Ohara has achieved the processing of the highprecision diffraction optical components…

PL-501 Book.book

PL-501 Book.book

…example, PL-501L-670T-500-45°)
Table 2-5. Terms Used in This Manual
FEATURE DEFINITION
Fan Angle or Line Length
Length of flat top profile, measured at 80% intensity
clip levels. Reported in degrees for the fan angle.
Straightness
Maximum deviation from the best…

COHR PowerLine DS 1017 3.pdf

COHR PowerLine DS 1017 3.pdf

Definition Description
Fan Angle or Line Length Length of flat top profile, measured at 80%
intensity clip levels. Reported in degrees for the
fan angle.
Straightness Maximum deviation from the best fit line.
Measured as the delta from the best fit line divided
by…

COHR MagnumII DS 1017 3.pdf

COHR MagnumII DS 1017 3.pdf

…Wavelength (nm) 680 808 808
Laser Power (mW) 1500 4000 7000
Final Beam Power (mW) 1200 3200 5600
Electrical Power 12VDC, 3A 12VDC, 5A 12VDC, 5A
Fan Angle 10°, 20°, 30°, 45°, 60°
Definition Description
Fan Angle or Line Length Length of flat top profile, measured at 80%…

COHR PL-501 DS 1119 3.pdf

COHR PL-501 DS 1119 3.pdf

…(nm) 445 670 808
Laser Power (mW) 375 500 1500
Final Beam Power (mW) 375 500 1500
Electrical Power 12VDC, 3A 5VDC, 2A 5VDC, 4A
Lens Fan Angle 5°, 10°, 20°, 30°, 45°, 60°
Definition Description
Fan Angle or Line Length Length of flat top profile, measured at 80%…

UW Series 09-19-14 .cdr

UW Series 09-19-14 .cdr


MARKING
Technical data is subject to change without prior notice.
W W W. R O F I N . C O M
60.0
68.0
15°
2.0
4.5
32.0
26.5
18.0
24.4
24.5
40.0
LASER MARKING
UW Series, Workstations for Laser Marking Applications

CMM 12.6.indd

CMM 12.6.indd


laser light in the presence of an ultrahigh purity inert gas or in vacuum.
The pulsed krypton fluoride
(KrF) excimer laser is ideal for
photoreduction of monolayer GO films
for two reasons. Firstly, the deepultraviolet (DUV) 248 nm photons
produced by the laser are more…

COHR Mini DS 1017 3.pdf

COHR Mini DS 1017 3.pdf

…are also available as dots -- add "D" instead of "L" in the order code.
Definition Description
Fan Angle or Line Length Length of flat top profile, measured at 80%
intensity clip levels. Reported in degrees for the
fan angle.
Straightness Maximum deviation from the…

Microsoft Word - 2018 11 Whitepaper CleanWeld E

Microsoft Word - 2018 11 Whitepaper CleanWeld E

…weld. Most important, it enables the fiber laser to deliver these high
quality results at market enabling throughput levels, typically in the 8 m/min to 24 - 30 m/min
depending upon thickness and material.
Figure 8: Cross section, top view and bottom view of a profile weld in…

OBIS Galaxy Datasheet COHR 2018.pdf

OBIS Galaxy Datasheet COHR 2018.pdf

…(1.1 in.)
Top View
Side View
Optional FC/PC8
Angled Flat Connector
Distal End - Output
FC/UFC
Launch End - Input
MECHANICAL SPECIFICATIONS
FC/APC
Distal End - Output
FC Connector Key
Polarization
±2° Max.
Laser Aperture

COHR OBIS Galaxy DS 0519 3.pdf

COHR OBIS Galaxy DS 0519 3.pdf

…(2.0 in.)
169.6 mm
(6.7 in.)
25.4 mm
(1.0 in.)
228.6 mm (9.0 in.)
29.1 mm (1.1 in.)
Top View
Side View
Optional FC/PC8
Angled Flat Connector
Distal End - Output
FC/UFC
Launch End - Input
MECHANICAL SPECIFICATIONS
FC/APC

Genesis-Taipan-Series

Genesis-Taipan-Series

…(2.11 in.) 12.7 mm (0.5 in.) 15.24 mm (0.6 in.) 8-32 UNC-2B X 0.50 Deep (4X) 0.125 Dia. Dowel Pin (2X) 0.188 Dia. Thru (2X) This surface must be flat within 0.001 in. and have 32 µm finish or better within TEC mounting areas. Base Plate Requirements Front View Top View Rear View Laser Head Side View