Search Results

Refine

Result Type

1 - 12 of 17 Products for 'Laser Cooling Water Guidelines' Page 1 of 2 |

Laser Cooling Water Guidelines

00 Laser Cooling.book

00 Laser Cooling.book

Laser Cooling Water Guidelines for Innova® Ion Laser Systems 5100 Patrick Henry Drive Santa Clara, CA 95054

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the J-5 Series laser.
3. Oil free to…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the J-3 Series laser.
3. Oil free to…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…OEM Lasers Operator's Manual
3 - 12
Guidelines for Use of
Compressed Air for
Purge
If nitrogen is not available, the alternative is clean, dry, oil-free
compressed air. Compressed air is available in many facilities but
typically is contaminated with water and oil…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…OEM Lasers Preinstallation Manual
3 - 12
Guidelines for Use of
Compressed Air for
Purge
If nitrogen is not available, the alternative is clean, dry, oil-free
compressed air. Compressed air is available in many facilities but
typically is contaminated with water and…

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the J-5V Series laser.
3. Oil free to…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the J-3 Series laser.
3. Oil free to…

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

…on all material access gates
and doors.
Laser Power
Measurement
To accurately measure delivered laser power, a calibrated optical
power meter (detector head plus display console) is necessary.
Liquid (water) cooling is generally required for the detector head at

00 SabreMFreD Preinstall.book

00 SabreMFreD Preinstall.book

Guidelines
3
Cooling Water The Innova Sabre MotoFreD ion laser requires a flow of water to
cool the laser head and electrical components inside the power
supply. Because the properties of the cooling water are critically
important to the performance of the laser, the Innova…

00 Sabre Preinstall.book

00 Sabre Preinstall.book

laser in a room that is not air conditioned in high
humidity conditions
· Using cooling water that is not temperature controlled
· Leaving the cooling water on when the laser is not operating
for extended time periods
The parameters required to determine if the cooling water

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the E-400 Series laser.
3. Oil free…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…contaminated with water and oil vapors. The purity
requirements for the compressed air are:
1. Filtered to remove particles larger than 1 micron.
2. Dried so that dew point is 10°C (18°F) lower than the inlet
cooling fluid temperature to the E-1000 Series laser.
3. Oil free…