Search Results

1 - 12 of 410 Products for 'Laser Power Supply' Page 1 of 35 |

Laser Power Supply

High Power Laser | HighLight™ FL-1000P Pulsed Fiber Laser

High Power Laser | HighLight™ FL-1000P Pulsed Fiber Laser

…the Company’s standard, CW fiber laser products: passive cooled T-bar pumping modules tolerating single emitter faults, power supplies and the RCU control unit. The control unit offers numerous monitoring tasks and e-service capability. The HighLight FL1000P lasers deliver a maximum pulse energy of…

Verdi Lasers

Verdi Lasers

--> Verdi Lasers Verdi is a family of optically pumped semiconductor lasers (OPSL) and diode-pumped solid-state (DPSS) lasers with continuous wave power up to 20W at 532 nm. Verdi is the preferred pump laser for Ti:Sapphire oscillators and amplifiers. The Verdi G-Series (OPSL technology) is…

OBIS Power Supply

OBIS Power Supply

Laser Remote and Power Supply
* Universal input connection (IEC-320)
* Compatible with 96-264 Volts AC input. Provides regulated 12 VDC output
* Cord length 1.2m (48 inches) Datasheet OBIS Single Laser Remote Drawing OBIS Single Laser Remote Power Supply Full-Feature Laser Remote and Power Supply -…

OBIS Galaxy Laser Combiner

OBIS Galaxy Laser Combiner

Laser Combiner with Lasers and Laser Box Part Number The base model of the OBIS Galaxy Integrated System includes: OBIS Galaxy Laser Combiner compatible with 405, 445, 488, 514, 532, 561, 590, 640 nm, Laser Box with Power Supply and Control Software, OBIS 405 nm LX 50 mW Fiber Pigtailed Laser, OBIS…

DIAMOND J-Series Lasers

DIAMOND J-Series Lasers

…speed, while minimizing the heat affected zone. An integrated RF power supply in J-Series lasers eliminates the traditional RF umbilical to enhance reliability and lower cost of ownership. J-Series products are available in powers ranging from 150W to 500W, and output wavelengths of 10.6 µm and 9.4…

Coherent Magnum II Laser Operator's Manual

Coherent Magnum II Laser Operator's Manual


To prepare the product for shipping:
1. Repack the laser in an ESD-safe bag.
2. Repack the laser in an ESD-safe foam and black box.
3. Repack the power supply in a box.
4. Place the laser and power supply in the system box.
5. Replace the top foam over the parts.…

HyperRapid NX/NXT - Industrial Picosecond Laser

HyperRapid NX/NXT - Industrial Picosecond Laser

…HyperRapid NX laser head is a self-contained system where all optical elements, control electronics, and thermo-mechanical management are integrated. It complies with state-of-the-art safety regulation and it is complemented by a selection of off-the-shelf chillers and power supplies to offer the…

Picosecond laser

Picosecond laser

…of the laser system
optional freq.-conversion with fixed output
Connecters Hyper Rapid The connecters for the Hyper Rapid are located on the rear
side of the power supply P90. The application signal connecters are located on the rear side of the laser head:
Figure 5: Power supply

INNOVA 70C Ion Laser

INNOVA 70C Ion Laser

…0.5% 1 All powers are listed in Watts. Guaranteed power specifications for standard systems are indicated in bold print. All power specifications, except multiline visible and IR, are TEM00. 2 All beam specifications are measured at specified output powers at 514.5 nm for argon lasers and 47.1 nm…

DC Series, CO2 Lasers for Cutting

DC Series, CO2 Lasers for Cutting

…the integrated gas bottle eliminates the need for an external gas supply. Up to the power range of 5 kW, the lasers run with a gas consumption of only 0.1 l/h. Furthermore, the energy-saving standby operation leads to minimal power consumption. The DC Series Series control offers extended monitoring…

Laser Power Sensors

Laser Power Sensors

…- Laser Power A diverse portfolio of nearly 100 different standard laser power sensors over a broad range of laser output characteristics allowing you to select a system to best meet your particular needs. This diversity enables laser power measurement over an extremely broad range of laser output…

Desktop Compact Laser Welding System

Desktop Compact Laser Welding System

…workshops and institutes and is hence the ideal system for the entry into laser technology. The Desktop is ergonomically optimized and can be placed on any desk. The air-cooled system requires only a one-phase power supply. The workpiece can be positioned via stereo microscope and cross-hair. The…