Search Results

37 - 48 of 73 Products for 'Laser Shutter' Page 4 of 7 |

Laser Shutter

00 Sabre Preinstall.book

00 Sabre Preinstall.book

Shutter
Interlock
This interlock is connected to the external shutter in the laser head.
As long as the circuit is closed, the external shutter can be opened
and closed from the Remote Control Module through the system
software. If the circuit is opened, the external shutter

COHR OBISfamily DS 0818 8.pdf

COHR OBISfamily DS 0818 8.pdf

…line regulation <0.5%.
MECHANICAL SPECIFICATIONS
OBIS LX/LS
38 mm
(1.5 in.)
Status
Indicator
Safety
Shutter
Laser Exit Aperture
M6 X 0.75 Thread
2.54 mm Deep
OEM Label
Fan
USB
SDR
Power
40 mm
(1.57 in.)

COHR OBISfamily DS 0719 2.pdf

COHR OBISfamily DS 0719 2.pdf

…line regulation <0.5%.
MECHANICAL SPECIFICATIONS
OBIS LX/LS
38 mm
(1.5 in.)
Status
Indicator
Safety
Shutter
Laser Exit Aperture
M6 X 0.75 Thread
2.54 mm Deep
OEM Label
Fan
USB
SDR
Power
40 mm
(1.57 in.)

COHR OBISfamily DS 0119 3.pdf

COHR OBISfamily DS 0119 3.pdf

…line regulation <0.5%.
MECHANICAL SPECIFICATIONS
OBIS LX/LS
38 mm
(1.5 in.)
Status
Indicator
Safety
Shutter
Laser Exit Aperture
M6 X 0.75 Thread
2.54 mm Deep
OEM Label
Fan
USB
SDR
Power
40 mm
(1.57 in.)

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

…1, 1M, 2, and 2M lasers
2. Laser radiation emission indicator (LED turning on when laser
is powered) for lasers > 700 nm
3. A permanently attached beam attenuator (a shutter or switch)
Class 3B
1. All items mentioned for Class 3R lasers
2. Laser radiation emission…

EnergyMax-USB/RS Software Installation and Quick Start Guide

EnergyMax-USB/RS Software Installation and Quick Start Guide

…to your PC and begin taking energy measurements using the EnergyMax PC software.
WARNING!
Follow all laser safety procedures. The laser
must be switched OFF or shuttered before
running the tutorial presented in this section.
NOTICE!
For instructions on communicating…

book.book

book.book

…opening the laser
shutter.
· Exercise extreme caution when using solvents in an area with any laser.
· Post laser warning signs in the area of the laser beam to alert those present.
· Limit access to the laser to trained and qualified users who are familiar with laser
safety…

00 Legend Elite Preinstallation.book

00 Legend Elite Preinstallation.book

…terminate the pump laser by activating a shutter
mechanism as well as removing power from the infrared diodes in
the pump laser power supply. While active, the interlock defeats are
directly visible by anyone near the laser. It is not possible to replace
the laser cover while the…

OBIS LaserSafety Installation QSG 11-85-44 9 RevAF COVERS.fm

OBIS LaserSafety Installation QSG 11-85-44 9 RevAF COVERS.fm

…to open
the mechanical front
shutter to allow light
emission.
4 5
Apply 12V power to the OBIS.
OBIS starts emitting light after it is thermally
stabilized. During stabilization, the LED
indicator on top of the laser blinks green.
When stabilized, the…

EnergyMax-USB/RS User Manual

EnergyMax-USB/RS User Manual

…your PC and start taking energy measurements
using the EnergyMax PC software.
WARNING!
Follow all laser safety procedures. The laser must be switched
OFF or shuttered before running the tutorial given in this
section.
NOTICE!
For instructions on communicating with…

Libra PreInstallation.book

Libra PreInstallation.book

…a shutter mechanism as well as
removing power from the infrared diode lasers in each power supply.
While installed, the interlock defeats are directly visible by anyone
near the laser. It is not possible to replace the laser cover while the
interlocks are installed
The laser

COHR ULN DS 1117 2.pdf

COHR ULN DS 1117 2.pdf

…Divergence (mrad) 1
Laser Drive Ultra-Low Noise (ULN)
Power Supply Included (dual voltage)
Connector 5-pin DIN
Part Number 31-0144-000
MECHANICAL SPECIFICATIONS
NOTE: Line generator modules (0220-936-00 and 31-0268-000)
do not included shutter.
4.8 mm