Search Results

1 - 12 of 63 Products for 'Laser Shutter' Page 1 of 6 |

Laser Shutter

Coherent Magnum II Laser Operator's Manual

Coherent Magnum II Laser Operator's Manual

…2-1).
Shutter The shutter should be kept closed when the laser is not in use--refer
to Figure 2-1 (p. 2-1). Before turning ON the power, the shutter
should be opened (shutter lever in the upper position, towards "I").
Likewise, the shutter should be closed (shutter lever in the…

Picosecond laser

Picosecond laser

…The Status connector is an interface on the back of the power
supply, that can be used to output the present state of the laser
system (laser diodes, shutter, interlock).
The Status connector is an 8-pin female circular connector
(also called DIN-connector, refer to DIN EN…

Revolution High-Power Q-Switched Laser System Preinstallation Manual

Revolution High-Power Q-Switched Laser System Preinstallation Manual

…nearby personnel time to prepare for laser radiation
emission.
Beam Safety
Shutter
A solenoid-actuated safety shutter is mounted in the optical cavity to
interrupt laser action when necessary. The shutter is actuated when
the laser is turned on (either by pressing the…

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

…terminate the pump laser by activating a shutter
mechanism as well as removing power from the infrared diodes in
the pump laser power supply. While active, the interlock defeats are
directly visible by anyone near the laser. It is not possible to replace
the laser cover while the…

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…terminate the pump laser by activating a shutter
mechanism as well as removing power from the infrared diodes in
the pump laser power supply. While active, the interlock defeats are
directly visible by anyone near the laser. It is not possible to replace
the laser cover while the…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System


prevents laser emission.
Shutter Interlock The shutter will not open unless the shutter interlock circuit is
closed. If the shutter interlock (EMBS) circuit is opened while the
laser is operating, it will cause the shutter to close but will not turn
the laser off.
For…

Microsoft Word - Understand Different Laser Beam  Rev 1 Final.doc

Microsoft Word - Understand Different Laser Beam Rev 1 Final.doc

…sensor
is not being recorded or is otherwise invalid
(analogous to a camera shutter being closed).
For CW laser sources this period is not
important, but for pulsed laser systems the
laser pulse must either not be generated during
the period of vulnerability, or the…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

laser safety purpose only.
This shutter is not to be used for beam modulation (as a `process
shutter').
Table 4-7. Extended Interface Signal Descriptions
IDENTIFICATION BRIEF DESCRIPTION CONNECTION
INPUT SIGNALS
Shutter Command
Opens and closes shutter (if shutter

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

laser safety purpose only.
This shutter is not to be used for beam modulation (as a `process
shutter').
Table 4-7. Extended Interface Signal Descriptions
IDENTIFICATION BRIEF DESCRIPTION CONNECTION
INPUT SIGNALS
Shutter Command
Opens and closes shutter (if shutter

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

laser safety purpose only.
This shutter is not to be used for beam modulation (as a `process
shutter').
Table 4-7. Extended Interface Signal Descriptions
IDENTIFICATION BRIEF DESCRIPTION CONNECTION
INPUT SIGNALS
Shutter Command
Opens and closes shutter (if shutter

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

laser safety purpose only.
This shutter is not to be used for beam modulation (as a `process
shutter').
Table 4-7. Extended Interface Signal Descriptions
IDENTIFICATION BRIEF DESCRIPTION CONNECTION
INPUT SIGNALS
Shutter Command
Opens and closes shutter (if shutter

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

laser safety purpose only.
This shutter is not to be used for beam modulation (as a `process
shutter').
Table 4-7. Extended Interface Signal Descriptions
IDENTIFICATION BRIEF DESCRIPTION CONNECTION
INPUT SIGNALS
Shutter Command
Opens and closes shutter (if shutter