Search Results

73 - 84 of 132 Products for 'Laser Tube' Page 7 of 11 |

Laser Tube

MetaBEAM1000c Pre.book

MetaBEAM1000c Pre.book

…should never be set below the ambient
dew point. Operating in this condition can cause condensation
that will permanently damage the laser tube. Damage caused by
condensation is not covered under warranty.
Table 1-4. Chiller Requirements
CHILLER COOLING
CAPACITY (MIN)…

COHR AutomaticTubeMarker DS 1019 7.pdf

COHR AutomaticTubeMarker DS 1019 7.pdf

AutoTube Marker Fully-Automated Robotic Laser System The Automatic Tube Marking System is a robotic tool for precision laser marking of high-value tubular parts, such as those used in medical devices. It provides a complete, automated solution allowing unattended operation. It incorporates robotic…

COHR MaterialsProcessingBrochure 0816revA 3.pdf

COHR MaterialsProcessingBrochure 0816revA 3.pdf

…construction of the laser tube, solid-state pulser,
advanced gas management and fully integrated data logging are
some of the other key features which are the basis for the ease-of-use
and high longevity of Excimer lasers.
Applications of Excimer laser covers a large range…

Photonics Spectra - September 2016

Photonics Spectra - September 2016

…which the discharge is
equilibrated between the pair of laser oscillators is another feature contributing to
the low pulse-to-pulse variations and excellent timing synchronization of the two
oscillators. The two laser tubes and their
solid-state pulsed power supplies are, in

Microsoft Word - COHR HeavyMetalPipeCutting WP 0519

Microsoft Word - COHR HeavyMetalPipeCutting WP 0519

…discharge geometry enables a relatively
compact laser head in contrast to traditional gas lasers with long plasma tube discharges.
Moreover, in lasers like the Coherent DC 030, the RF power supply is located within the
compact laser head, eliminating the cost and potential reliability…

Industrial Photonics - October 2017

Industrial Photonics - October 2017

…compact laser head in contrast to traditional gas lasers with
long plasma tube discharges. Moreover, in lasers like the
Coherent-Rofin DC 030, the RF power supply is located
within the compact laser head, eliminating the cost and
Figure 3. In a slab discharge laser such as the…

COHR IndyStar DS 0818 7.pdf

COHR IndyStar DS 0818 7.pdf

IndyStar Fast Pulse, High Precision Processing IndyStar is a rugged high-duty cycle excimer laser designed for fast pulse frequency applications as high as 2000 Hz. Based on proven ALMETA tube technology, the Semi-S2 certified IndyStar operates over many billion pulses at ultra-short 193 nm and 248…

Paladin Advanced Preinstallation.book

Paladin Advanced Preinstallation.book

Paladin Mode Locked UV Laser Preinstallation Manual
4 - 2
PALADIN 355-4 (4-WATT SYSTEM) 1104091
Head 1104092
Paladin Advanced 355 P/S Master W/O FAPs 1151419
Paladin 355 Tube Set 1096057
Pump Module Assembly 1104473
Serial Cable for chiller remote temperature…

COHR IndyStar DS 1219 1.pdf

COHR IndyStar DS 1219 1.pdf

IndyStar Fast Pulse, High Precision Processing IndyStar is a rugged high-duty cycle excimer laser designed for fast pulse frequency applications as high as 2000 Hz. Based on proven ALMETA tube technology, the Semi-S2 certified IndyStar operates over many billion pulses at ultra-short 193 nm and 248…

Avia preinstall.book

Avia preinstall.book

…in the laser head. Connect the plastic tubing from the
chiller to the laser head (flow direction is not important) and fill the
chiller with distilled water. The water control temperature should be
set to maintain the laser baseplate temperature at about 25ºC for best
laser

CMM 11.1.indd

CMM 11.1.indd

…is passed through the inside of the
tubing during processing to minimise
damage on the inside surface of the tube
(Figure 2).
Results
The system can be integrated with
either an IR wavelength or green
wavelength Monaco laser to perform
high-speed cylindrical…

Coherent

Coherent

…our DPSS lasers used
in microelectronics and scientific applications in Hannover, Germany. Our excimer gas laser products
are manufactured in G¨
ottingen, Germany. We refurbish excimer tubes at our manufacturing site in
South Korea. We manufacture the fiber-based lasers and a…