Ask a Question
Coherent

Search Results

1 - 12 of 45 Products for 'Linear Stage' Page 1 of 4 |

Linear Stage

Lasers | Photonics Handbook®

Lasers | Photonics Handbook®

…reason, they are pumped by CPA pico- or femtosecond amplifiers producing at least several microjoules. The addition to an OPA/OPO of one or more stages of harmonic generations and mixing yields a range of wavelengths that can cover 200 nm to 20 µm. Common laser types For many years, the most common…

Mephisto MOPA

Mephisto MOPA

…amplification stages, resulting in a Master Oscillator Power Amplifier (MOPA) configuration. Mephisto MOPA laser incorporates a Mephisto S oscillator followed by 1 to 4 stages of power amplification, pumped by fiber-coupled laser diode pump modules. The seed and amplification stages are fully…

UV Beam Prosp. engl.

…Metrolux Pro Scan software allows one to analyze the short and the long axis. For this purpose the MicroLas Line Beam Optics is equipped with a linear stage which holds the CCD camera/objective. The camera is moved along the 200-mm Line Beam Optics axis so that it takes Line Beam profiles stepwise…

Laser Focus World - February 2016

Laser Focus World - February 2016

…between fabrication of different FBG types without operator handling. The optical fiber is mounted in a modular fixture and is positioned on a linear stage that allows FBGs to be written along the fiber in a precise position in an automated fashion. Moreover, the total system cost is less than what…

Talisker Sapphire Scribing Whitepaper final.pdf

Talisker Sapphire Scribing Whitepaper final.pdf

…Specifically, it has already been demonstrated to operate at speeds of up to 500 mm/s, and the upper limitation in this case was caused by the linear motion stage and not the laser process. The narrow scribes and minimal heat affected zone also allow for the narrowest possible streets on the wafer,…

Talisker Sapphire Scribing Whitepaper final.pdf

Talisker Sapphire Scribing Whitepaper final.pdf

…Specifically, it has already been demonstrated to operate at speeds of up to 500 mm/s, and the upper limitation in this case was caused by the linear motion stage and not the laser process. The narrow scribes and minimal heat affected zone also allow for the narrowest possible streets on the wafer,…

Micromachining-of-Sapphire-Wafers-for-LED-Production-using-Picosecond-Lasers.pdf

Micromachining-of-Sapphire-Wafers-for-LED-Production-using-Picosecond-Lasers.pdf

…Specifically, it has already been demonstrated to operate at speeds of up to 500 mm/s, and the upper limitation in this case was caused by the linear motion stage and not the laser process. The narrow scribes and minimal heat affected zone also allow for the narrowest possible streets on the wafer,…

Microsoft Word - LabMaxUniqueBenefitsPerformanceDownloadr2~.doc

Microsoft Word - LabMaxUniqueBenefitsPerformanceDownloadr2~.doc

…to 20 mA with a bandwidth of 159 Hz with only two gain stages also provides the highest level of linearity and resolution of any Coherent meter: 5 digits of measurement resolution +/-1% measurement accuracy Non-linearity due to gain stages is highly minimized due to use of only a single change…

502 Lambda USA Reprint.QXD

502 Lambda USA Reprint.QXD

…side-pumped geometry in both oscillator and amplifier stages to allow scalability. The optical setup included /4 plate and a focusing lens with a 50- to 150-mm focal length in the beam path. Samples were translated with precision X-Y stages for linear cuts, with holes either percussion-drilled or…

SolidStateLasers 2014.pdf

SolidStateLasers 2014.pdf

…speed and speed comes from the repetition rate of the laser. `For most systems, repetition rate is limited by the motion system, by the linear or rotating stages,' commented Röhner. `Normally, the cutting geometry is not in a straight line; it's a complex 2D structure which limits the processing…

Layout 1

Layout 1

…aperture and focused it onto the Teflon surface with a demagnification as high as 20 . The sample was translated onto an X-Y stage to create patterns both of linear and square crossed grooves. In this way, several 1 1-mm areas on each polished sample disk were laser-machined with high lateral…

Layout 1

Layout 1

…aperture and focused it onto the Teflon surface with a demagnification as high as 20 . The sample was translated onto an X-Y stage to create patterns both of linear and square crossed grooves. In this way, several 1 1-mm areas on each polished sample disk were laser-machined with high lateral…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions