Ask a Question
Coherent
Search Results
Refine

Result Type

1 - 12 of 21 Products for 'Low Coolant Level' Page 1 of 2 |

Low Coolant Level

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 10 Coolant Composition The recommended coolant composition is a mixture of clean distilled or de-ionized water and OPTISHIELD® Plus, a low toxicity, corrosion inhibitor. OPTISHIELD Plus is available from OptiTemp, Inc. and can be shipped…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 10 Coolant Composition The recommended coolant composition is a mixture of clean distilled or de-ionized water and OPTISHIELD® Plus, a low toxicity, corrosion inhibitor. OPTISHIELD Plus is available from OptiTemp, Inc. and can be shipped…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 10 Coolant Composition The recommended coolant composition is a mixture of clean distilled or de-ionized water and OPTISHIELD® Plus, a low toxicity, corrosion inhibitor. OPTISHIELD Plus is available from OptiTemp, Inc. and can be shipped…

00 E-250 Pre.book

00 E-250 Pre.book

…corrosion. Levels lower than the recommended amount may also encourage microbial growth, which can result in fouling and blockage of the cooling system. Also, only use fresh, clean coolant mix (OptiTemp recommends that the coolant be drained and replaced annually). Table 3-2. Recommended Coolant for…

00 E-250 Pre.book

00 E-250 Pre.book

…corrosion. Levels lower than the recommended amount may also encourage microbial growth, which can result in fouling and blockage of the cooling system. Also, only use fresh, clean coolant mix (OptiTemp recommends that the coolant be drained and replaced annually). Table 3-2. Recommended Coolant for…

00 E-250 Pre.book

00 E-250 Pre.book

…corrosion. Levels lower than the recommended amount may also encourage microbial growth, which can result in fouling and blockage of the cooling system. Also, only use fresh, clean coolant mix (OptiTemp recommends that the coolant be drained and replaced annually). Table 3-2. Recommended Coolant for…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Installation 3 - 11 · Water level low (yellow) · Water level critical (red) At initial installation, the yellow, red and the "Flow 1 LED" LEDs can turn on. If the LEDs turn on, continue to carefully add coolant to the system. When the yellow LED turns off, and remains turned off, disconnect the…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Installation 3 - 11 · Water level low (yellow) · Water level critical (red) At initial installation, the yellow, red and the "Flow 1 LED" LEDs can turn on. If the LEDs turn on, continue to carefully add coolant to the system. When the yellow LED turns off, and remains turned off, disconnect the…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Installation 3 - 11 · Water level low (yellow) · Water level critical (red) At initial installation, the yellow, red and the "Flow 1 LED" LEDs can turn on. If the LEDs turn on, continue to carefully add coolant to the system. When the yellow LED turns off, and remains turned off, disconnect the…

00 E-250 Pre.book

00 E-250 Pre.book

…main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump. Figure 1-6. Optional Laser Safety Shutter with Diode Pointer

00 E-250 Pre.book

00 E-250 Pre.book

…main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump. Figure 1-6. Optional Laser Safety Shutter with Diode Pointer

00 E-250 Pre.book

00 E-250 Pre.book

…main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump. Figure 1-6. Optional Laser Safety Shutter with Diode Pointer

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions