Search Results

Refine
1 - 12 of 24 Products for 'Oscilloscope' Page 1 of 2 |

Oscilloscope

ModeMaster PC User Manual

ModeMaster PC User Manual

…1 - 6
Oscilloscope
Traces
The direct signal from the ModeMaster PC Scan Head detector can
be displayed on an oscilloscope by connecting the SCOPE
TRIGGER on the rear of the ModeMaster PC Control/Interface
Console to the External Trigger on the oscilloscope, connecting…

COHERENT LMC 2016-2017 Catalog .pdf

COHERENT LMC 2016-2017 Catalog .pdf

…lengthen the cable
when using the sensor with the oscilloscope.
1. To assure the accuracy of a pulse energy
measurement, make sure the oscilloscope is
calibrated properly. Also check the date for when
the oscilloscope is due for recalibration.
2. Select a scope that has…

2016-Ultrafast-Laser-Systems-Catalog.pdf

2016-Ultrafast-Laser-Systems-Catalog.pdf


1 In picosecond mode, the range and resolution are wavelength-dependent. Contact factory for details.
available for display on an oscilloscope or as a measurement by a computer DAC card.
The SSA's indexed internal mirror configuration allows
convenient sampling of pulses without…

Libra PreInstallation.book

Libra PreInstallation.book

Powderless latex or nitrile gloves
Laser Equipment

Power meter and head (e.g., Coherent FieldMate with LM10,
LM2 heads).

An oscilloscope (300 MHz or higher)
Table 3-5. Pre-installation Checklist
ACTIVITYAND
EQUIPMENT
GENERAL REQUIREMENTS REFERENCE(S)

J-Power Pro Energy Sensor DB-25-to-BNC Adapter

J-Power Pro Energy Sensor DB-25-to-BNC Adapter

…the sensor directly to the BNC connector. The peak voltage of the output (as referenced from baseline voltage) can then be measured using an oscilloscope or another analog-to-digital input device. The calibrated peak voltage represents the integrated energy of the laser pulse. Name J-Power Pro…

COHR HRNX SmartCleave DS 0718 3.pdf

COHR HRNX SmartCleave DS 0718 3.pdf

…HyperRapid NX SmartCleave: glass cutting (left), automotive dashboard cutting (right)
HyperRapid NX Smartcleave Burst Mode Operation
Oscilloscope trace showing 5 pulses in the burst at 100 kHz repetition rate. The pulses in the burst are separated by 25 ns
Time (a.u.)
Signal…

00 Legend Elite Preinstallation.book

00 Legend Elite Preinstallation.book

…Out 1 delay
HSD 2 trig Out 2 delay
BWD BWD
HV 1 HV 1
Sync out delay
RF sync
Remote
motor
control
Oscilloscope
Legend Elite
Optical Bench Assembly
Chiller
Chiller
IN
OUT
IN
OUT
Air IN
Air OUT
RETURN…

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…10 W capacity (45 W for entire Revolution
beam)
· A spectrometer with a spectral window of 700 to 900 nm
· 300 MHz or better oscilloscope and BNC cable
· IR viewer
Table 3-4. Astrella Cable & Hose Lengths
MODEL
AC POWER CORD
LENGTH
UMBILICAL /WATER…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…presents a pulsed dynamic load to the DC power
supply. To observe the effect of laser modulation on the DC power
supply, connect an oscilloscope across the DC input terminals of the
RF power module while applying modulation pulses to the laser.
Coherent has qualified air-cooled…

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

…10 W capacity (45 W for entire Revolution
beam)
· A spectrometer with a spectral window of 700 to 900 nm
· 300 MHz or better oscilloscope and BNC cable
· IR viewer
Table 3-4. Astrella Cable & Hose Lengths
MODEL
AC POWER CORD
LENGTH
UMBILICAL / WATER…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…presents a pulsed dynamic load to the DC power
supply. To observe the effect of laser modulation on the DC power
supply, connect an oscilloscope across the DC input terminals of the
RF power module while applying modulation pulses to the laser.
Coherent has qualified air-cooled…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…presents a pulsed dynamic load to the DC power
supply. To observe the effect of laser modulation on the DC power
supply, connect an oscilloscope across the DC input terminals of the
RF power module while applying modulation pulses to the laser.
Coherent has qualified air-cooled…