Search Results

Refine

Result Type

1 - 12 of 12 Products for 'Over Current Fault' Page 1 of 1 |
  • 1

Over Current Fault

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

fault code bit mapping.
Table 5-2. Fault Bit Codes
Bit Mask Bit Label Definition
1 2 Diode Temperature Fault Diode temperature out of range
2 4 Internal Temperature Fault Internal temperature out of range
4 10 12C Error 12C bus error
5 20 Over Current Diode over current

Coherent Terms and Conditions of Purchase %28NA%29 D13-78-43 AC.pdf

Coherent Terms and Conditions of Purchase %28NA%29 D13-78-43 AC.pdf

…returned to Supplier at Supplier's expense. In the event a blanket Purchase Order is initiated, Coherent reserves the right to schedule deliveries over a twelve-month period. The total blanket Purchase Order quantity represents Coherent's best estimated usage and is not a commitment to purchase.…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…to aging
Fault output is an open collector of the transistor that allows wire junction OR functionality with fault signals
from other devices. The output can tolerate voltage up to 30V and can drain the current up to 100 mA. The circuit
is protected from over current by recoverable…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…purposes of fault detection, shutter
open, shutter moving, or neither open nor closed are tested for determining a
fault condition. A Shutter Latching Fault causes system shutdown.
19 (+) and 7 (-) Reserved Do not connect.
20 (+) and 8 (-)
Over Temperature
Fault

UKPOTermsAndCondiitions 2014.pdf

UKPOTermsAndCondiitions 2014.pdf

…Claims which arise solely from the negligence, misconduct or other fault of Coherent, or to claims covered in whole by Section 7. It shall apply, however, if a Claim is the result of joint negligence, joint misconduct, or joint fault of Coherent and Supplier, but in such case the amount of the Claim…

Book.book

Book.book

Operation
5 - 9
2048 Over Current Laser current exceeded 120% of
the new system current--result of
diode degradation over time
Contact Coherent Technical Support
4096 Reset Clock Internal error caused system clock
reset
8192 System Time Out Command is not…

book.book

book.book

…integer form. The 32-bit word represents a bit-mapped fault
indicator.
As an example, if the base plate and laser diode temperature limits are both exceeded,
the system fault query returns:
00000020 Diode Over Current
QUERY SOUR:TEMP:DIOD?
REPLY <x.x>

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…purposes of fault detection, shutter
open, shutter moving, or neither open nor closed are tested for determining a
fault condition. A Shutter Latching Fault causes system shutdown.
19 (+) and 7 (-) Reserved Do not connect.
20 (+) and 8 (-)
Over Temperature
Fault

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

…purposes of fault detection, shutter
open, shutter moving, or neither open nor closed are tested for determining a
fault condition. A Shutter Latching Fault causes system shutdown.
19 (+) and 7 (-) Reserved Do not connect.
20 (+) and 8 (-)
Over Temperature
Fault

00 E-250 Pre.book

00 E-250 Pre.book

…purposes of fault detection, shutter
open, shutter moving, or neither open nor closed are tested for determining a
fault condition. A Shutter Latching Fault causes system shutdown.
19 (+) and 7 (-) Reserved Do not connect.
20 (+) and 8 (-)
Over Temperature
Fault

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…purposes of fault detection, shutter
open, shutter moving, or neither open nor closed are tested for determining a
fault condition. A Shutter Latching Fault causes system shutdown.
19 (+) and 7 (-) Reserved Do not connect.
20 (+) and 8 (-)
Over Temperature
Fault

Purchase Order Terms and Conditions %28UK%29.pdf

Purchase Order Terms and Conditions %28UK%29.pdf

…Claims which arise solely from the negligence, misconduct or other fault of Coherent, or to claims covered in whole by Section 7. It shall apply, however, if a Claim is the result of joint negligence, joint misconduct, or joint fault of Coherent and Supplier, but in such case the amount of the Claim…

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions