Search Results

Refine

Result Type

1 - 10 of 10 Products for 'Pulse Energy Percent' Page 1 of 1 |
  • 1

Pulse Energy Percent

Avia preinstall.book

Avia preinstall.book

pulsing.
0 = pulsing off.
1 = pulsing on.
PRINT PULSE ENERGY
?PEON
Indicates whether Pulse Energy is on or off.
0 = off.
1 = on.
PRINT PULSE ENERGY PERCENT
?PEP
Indicates Pulse Energy percentage.
PRINT PULSE MODE
?PM
Returns the pulse

Photonics Spectra - March 2018

Photonics Spectra - March 2018

…virtually unaffected by changes in the pulse rate up to several MHz; doubling the pulse rate only cuts the pulse energy by 50 percent (Figure 1). The pulsing flexibility also supports so-called seeder burst mode -- a group of two to five pulses at full energy and separated by the native repetition…

LabMax-Pro SSIM User Manual

LabMax-Pro SSIM User Manual

…expressed as an absolute power
or energy value, depending on which measurement mode is selected.
This command only applies to pyroelectric and fast power probes.
If a pyroelectric probe is attached, the minimum trigger level is
0.0001 percent of the maximum Joules rating of the…

Photonics Spectra - September 2016

Photonics Spectra - September 2016

…the energy stability of each individual oscillator is between 0.25 and 0.3
percent sigma, well within the LTPS process window -- in spite of the inevitable
variations in repetitively firing a plasma
discharge at tens of kilovolts. But, by combining and mixing the pulses from…

LabMax-Pro PC Software Installation and Quick Start Guide

LabMax-Pro PC Software Installation and Quick Start Guide

…as a percent
of the currently-selected energy range. The trigger level is a
threshold used to determine which signals will be collected as
energy measurements and which signals will be ignored as noise.
Setting the trigger level too high can result in actual energy pulses

Photonics Spectra - September 2017

Photonics Spectra - September 2017

…chromophores and energy transfer. A simplified
schematic of Fleming's setup (Figure 3)
shows how four different light pulses are
all derived from the same broadband femtosecond source using a simple diffractive
optical element. (The fourth pulse is used
for heterodyne…

COHERENT LMC 2016-2017 Catalog .pdf

COHERENT LMC 2016-2017 Catalog .pdf


& ENERGY
Custom
& OEM
BEAM
DIAGNOSTICS
CALIBRATION
& SERVICE
Power
& Energy
Meters
Laser
CrossReference
Index
Model
Name
Index
DB-25
Energy
Sensors
USB/RS
Energy
Sensors…

EU Photonics Flexible Displays.pdf

EU Photonics Flexible Displays.pdf

…covered
within each laser pulse ranges from
1 cm2 for a 250 mm line beam length to
3 cm2 for a 750 mm line beam length.
As a single shot per area is sufficient and
the overlap between the applied pulsed
is of the order of a few percent of the
line beam width, the…

Industrial Photonics - July 2018

Industrial Photonics - July 2018

…laser, achieving the necessary photon energy
through multiphoton absorption. However, given today's
laser capabilities and specifications, those processes are
less than 100 percent efficient.
At a rate of as much as tens of millions of pulses per
second, the result of even…

Lasers | Photonics Handbook®

Lasers | Photonics Handbook®

…10-ps
pulse width). This level of pulse energy can cater to some applications, but a large number of applications are served with pulse energies in the 100-µJ range.
One can use specialty fibers to increase the mode inside the fiber and thereby allow for larger pulse energies, but such…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions