Search Results

Refine

Result Type

1 - 12 of 12 Products for 'Purge Gas Filter' Page 1 of 1 |
  • 1

Purge Gas Filter

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB


Purge Gas
Filter
Assembly
1236040:
Replacement
filter cartridge
Purge Gas tubing
(between purge gas
supply and laser
system)
as required
1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas supply…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…tubing to carry the purge gas.
See "Preventive Maintenance" on page 6-1 in Section Six:
Maintenance and Troubleshooting for the routine maintenance
required for the purge gas filters.
Figure 3-5. Air Filter Dryer Unit
AIR OUT
1 2
1. Air Purge Filter Assembly; Part…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA


Purge Gas
Filter
Assembly
1236040:
Replacement
filter cartridge
Purge Gas tubing
(between purge gas
supply and laser
system)
as required
1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas supply…

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA


Purge Gas
Filter
Assembly
1236040:
Replacement
filter cartridge
Purge Gas tubing
(between purge gas
supply and laser
system)
as required
1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas supply…

00 E-250 Pre.book

00 E-250 Pre.book


Purge Gas
Filter
Assembly
1236040:
Replacement
filter cartridge
Purge Gas tubing
(between purge gas
supply and laser
system)
as required
1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas supply…

00 M5C Pre Install.book

00 M5C Pre Install.book

…CDA is barely detectable. The
laser only requires a few CFM of air for proper purging.
See "Purge Gas System Maintenance" on page 7-3 for the routine
maintenance required for the purge gas filters.
Human Machine
Interface (HMI)
and Networking
All M5C LMT systems…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…40°F). The
filter is shown in Figure 3-5 and is widely available.
For additional information on the Air Filter Dryer Unit, refer to "Air
Filter Dryer Unit" on page D-2 of this manual.
NOTICE!
It is the responsibility of the customer to provide purge gas of
either…

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC


Purge Gas Filter
Assembly
1236040:
Replacement
filter cartridge
Purge Gas tubing
(between purge gas
supply and laser
system)
as required
1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene
tubing to connect the purge gas supply…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…contact with
the coolant
No
Purge Gas
(Regulated Supply)
1
Used to displace atmosphere of air within the laser
head and the RF power module; typically N2
or
clean, dry air (CDA)
No
Purge Gas Filter
N/A if using
N2
; required

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…in contact with
the coolant
No
Purge Gas
(Regulated Supply)
1
Used to displace atmosphere of air within the laser
head and the RF power supply; typically N2 or
clean, dry air (CDA).
No
Purge Gas Filter
N/A if using
N2; required
if…

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

…typically N2
or clean, dry air (CDA)
No
Purge Gas Filter
N/A if using
N2
; required if
using CDA
Removes water vapor and particulates from compressed air. No
Purge Gas tubing
(between purge gas
supply and laser
system)
as required

COHR DIAMOND J-3-5 COlaser DS 0617 2.pdf

COHR DIAMOND J-3-5 COlaser DS 0617 2.pdf


Ambient Temperature 5 to 45°C (41 to 113°F)
Relative Humidity11 (non-condensing)(%) 95
Altitude 2000 m (6500 ft.)
Dry Purge Gas Requirements12 (cfm) >2
1 All specifications apply when the product is operated in accordance with the guidelines defined in the operators…