Search Results

Refine

Result Type

1 - 12 of 13 Products for 'Rf Cable' Page 1 of 2 |

Rf Cable

Book.book

Book.book

…impedance of
50 ohm..
1. Connect the laser as shown in "Section Three: Installation"
(p. 3-1).
2. Connect a signal generator cable (impedance Z = 50 )
between the laser head and the RF-source (maximum
frequency < 150 MHz).
Figure 5-1. Pulse Timing Diagrams

00 E-250 Pre.book

00 E-250 Pre.book

…Installation
3 - 35
- 48 VDC Cable
Connection and
Optional
Grounding of
RF Module
The E-Series RF module - 48 VDC return is internally grounded
directly to the chassis ground of the laser system. The - 48 VDC
power supply cable from the DC power supply is…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…let the system equilibrate
to room temperature before opening the moisture seal bag.
16. Locate and remove the sealed plastic bag containing the RF
power module system cable (Figure 22).
Figure 21. Opening the Moisture Seal Bag
Figure 22. RF Power Module System Cable

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…system on a cart capable of supporting and
transporting 173 kg (381 lbs.) (Figure 16).
12. Locate and remove the sealed plastic bag containing the RF
power supply system cable (Figure 17).
Figure 16. Place Laser System on Cart
Figure 17. RF Power Supply System Cable

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

…+ 48 VDC cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.

Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

…+ 48 VDC cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.
Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.

Diamond J-5 Series OEM Lasers Preinstallation Manual, Rev. AC

…Never connect the DC supplies' cables to the laser with their
polarities reversed. Applying power under this condition will
severely damage the RF module.
- 48 VDC Cable
Connection and
Optional
Grounding of
RF Module
The J-Series RF module - 48 VDC return is…

Diamond J-2 Series OEM Lasers Preinstallation Manual, Rev. AB

…the RF module will
be severely damaged requiring complete replacement.
NOTICE!
When connecting the DC power supply's + 48 VDC cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.
Never connect the DC supplies' cables to…

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

Diamond J-3-5 Series OEM Lasers Preinstallation Manual, Rev. AA

…the RF module will
be severely damaged requiring complete replacement.
NOTICE!
When connecting the DC power supply's + 48 VDC cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.

Never connect the DC supplies' cables to…

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

DIAMOND J-5V Series OEM Lasers Preinstallation Manual, Rev. AA

…Installation
3 - 29
DC Return Cable
Connection and
Optional
Grounding of
RF Module
The J-Series RF module DC Return is internally grounded directly
to the chassis ground of the laser system. The DC Return power
supply cable from the DC power supply is to…

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

Diamond J-3 Series OEM Lasers Preinstallation Manual, Rev. AC

…the RF module will
be severely damaged requiring complete replacement.
NOTICE!
When connecting the DC power supply's + 48 VDC cable to the
laser's + 48 RF filtering connector, use two wrenches to prevent
damaging the connector.
Never connect the DC supplies' cables to…

Diamond g50 100 Quiksetup.pdf

Diamond g50 100 Quiksetup.pdf

…unidad a una fuente de alimentación de
48 VDC usando un cable corto para alta corriente, y
asegúrese de que haya 48 Voltios. El polo positivo va
al filtro y tierra se conecta al terminal de tierra.
4. Conecte el cable DB25 a su circuito de control.
5. Ajuste el generador de…

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions