Search Results

Refine
1 - 10 of 10 Products for 'Rf Generator' Page 1 of 1 |
  • 1

Rf Generator

Pulse Switch for Mira 900

Pulse Switch for Mira 900

generation option provides conversion efficiencies up to 40% May be purged for tuning above 920 nm Control box (supplied) includes: Internal frequency divider (1:2 to 260,000) External trigger input (TTL) Digital and analog phase adjust of RF pulse (360°) Electronic delay Synchronization and RF

Ultrafast Oscillator Accessories

Ultrafast Oscillator Accessories

…existing and new ultrafast laser set-ups. Contact Us About This Product Close All Ultrafast Oscillator Accessories Products Harmonic Generator Harmonic Generator Extremely flexible and adaptable second-harmonic, third-harmonic, and fourth-harmonic wavelength extension accessory for Coherent’s entire…

Diamond g50 100 Quiksetup.pdf

Diamond g50 100 Quiksetup.pdf

…OEM del laser G-50/100.
DESCRIZIONE
Il modello G-50/100 e' un dispositivo OEM composto da un
resonatore laser ed un generatore di Radiofrequenza (RF)
integrati. Come ingressi sono richiesti 48 VDC, acqua di
raffreddamento e vari segnali di controllo.
STANDARD DI…

00 E-250 Pre.book

00 E-250 Pre.book

Control Interfaces
4 - 7
Drive Circuit for
RF Power Supply
An example of a drive circuit to interface to the ENABLE and
MODULATION inputs is shown in Figure 4-4.
The MODULATION input interface shown in Figure 4-3 is
designed to be driven by a differential line…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual
4 - 8
Drive Circuit for
RF Power Module
An example of a drive circuit to interface to the ENABLE and
MODULATION inputs is shown in Figure 4-4.
The MODULATION input interface shown in Figure 4-4 is
designed to be…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual
4 - 8
Drive Circuit for
RF Power Module
An example of a drive circuit to interface to the ENABLE and
MODULATION inputs is shown in Figure 4-4.
The MODULATION input interface shown in Figure 4-4 is
designed to be…

Book.book

Book.book

…input impedance of
50 ohm..
1. Connect the laser as shown in "Section Three: Installation"
(p. 3-1).
2. Connect a signal generator cable (impedance Z = 50 )
between the laser head and the RF-source (maximum
frequency < 150 MHz).
Figure 5-1. Pulse Timing Diagrams…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…from the laser head
through the RF power module and out to the drain.
From DC supply (+) Connects +48 VDC from the DC power supply to the RF power module. Apply
190 in.-lbs. (21.4 N·m) torque to nut supplied.
From DC supply (-) Connects the RF power module - 48 VDC return to the…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…to the RF power supply.
Use a 3/4" wrench. Apply 190 lb.-in. (21.4 N·m) torque to nut supplied.
9
Laser to RFPS
connector cable
Connector cable provides internal laser head to RFPS signals.
10
48 VDC Return (-)
(terminal)
Connects the RF power supply…

COHR MaterialsProcessingBrochure 0816revA 3.pdf

COHR MaterialsProcessingBrochure 0816revA 3.pdf

…and factory integration.
CO and CO2:
Coherent's Diamond E-Series and J-Series lasers are sealed, pulsed
CO2 systems with a built-in RF power supply, which increases
reliability and simplifies integration. A full suite of on-board diagnostics enables proactive maintenance to…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions