Ask a Question
Coherent
Search Results
13 - 24 of 390 Products for 'Rf Power Supply' Page 2 of 33 |
Related Categories: 100w Co2 Laser | Gem100 | Gem-100l | Co2 | Diamond

Rf Power Supply

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…and RF power supply) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas line between the laser head and RF power supply Yes Tee 1 1/4 inch (6 mm) OD Tee for splitting the purge gas tubing at the laser head and RF power supply Yes Purge…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…(the DC Power Supply will restrict the flow). DC Power Supply OUT IN SUPPLY SUPPLY SUPPLY 0 GPM 6.5 0 GPM 2-3 0 GPM 6.5 Chiller RETURN SUPPLY Laser Head RF Power Supply Flow loop shown is incorrect without a Bypass around the DC Power Supply. In a serial loop, the DC Power Supply will restrict…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…(the DC Power Supply will restrict the flow). DC Power Supply OUT IN SUPPLY SUPPLY SUPPLY 0 GPM 6.5 0 GPM 2-3 0 GPM 6.5 Chiller RETURN SUPPLY Laser Head RF Power Supply Flow loop shown is incorrect without a Bypass around the DC Power Supply. In a serial loop, the DC Power Supply will restrict…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…cables for the "48V Return" negative (-) connections. Apply 190 lb.-in. (21.4 N·m) torque to both supplied hex nuts. Figure 23. RF Power Supply DC Input Terminal Fasteners RF POWER SUPPLY +48VDC and -48VDC RETURN TERMINALS DC Power Supply Cable 1 2 3 1 2 Flat WasherStar Washer Hex Nut3 Ring Lug Stud

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…and RF power supply) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas line between the laser head and RF power supply Yes Tee 1 1/4 inch (6 mm) OD Tee for splitting the purge gas tubing at the laser head and RF power supply Yes Purge…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…and RF power supply) 1 piece A short length of 1/4 inch (6 mm) OD Teflon, polyethylene or polypropylene tubing to connect the purge gas line between the laser head and RF power supply Yes Tee 1 1/4 inch (6 mm) OD Tee for splitting the purge gas tubing at the laser head and RF power supply Yes Purge…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 32 9. Cut the moisture seal bag along the groove between the laser head and RF power supply from eye-bolt to eye-bolt, then cut across the bag top at both ends (Figure 14). Figure 14. Cutting Top of Moisture Seal Bag

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 32 9. Cut the moisture seal bag along the groove between the laser head and RF power supply from eye-bolt to eye-bolt, then cut across the bag top at both ends (Figure 14). Figure 14. Cutting Top of Moisture Seal Bag

00 E-1000 PreInst.book

00 E-1000 PreInst.book

DIAMOND E-1000 Series OEM Lasers Preinstallation Manual 32 9. Cut the moisture seal bag along the groove between the laser head and RF power supply from eye-bolt to eye-bolt, then cut across the bag top at both ends (Figure 14). Figure 14. Cutting Top of Moisture Seal Bag

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…DC power supply to the RF power supply. Use a 3/4" wrench. Apply 190 lb.-in. (21.4 N·m) torque to nut supplied. 9 Laser to RFPS connector cable Connector cable provides internal laser head to RFPS signals. 10 48 VDC Return (-) (terminal) Connects the RF power supply ground to the DC power supply.

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…DC power supply to the RF power supply. Use a 3/4" wrench. Apply 190 lb.-in. (21.4 N·m) torque to nut supplied. 9 Laser to RFPS connector cable Connector cable provides internal laser head to RFPS signals. 10 48 VDC Return (-) (terminal) Connects the RF power supply ground to the DC power supply.

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…manual for mounting information. Since the DC power cables (available from Coherent) are 3 m (10 ft.) in length, position the power supply output terminals within reach of the RF power supply input terminals. Refer to Figure 22 for RF power supply connection points. Laser Head Indicators and…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions