Search Results

Refine

Result Type

1 - 12 of 32 Products for 'Socket' Page 1 of 3 |

Socket

Coherent Magnum II Laser Operator's Manual

Coherent Magnum II Laser Operator's Manual

…Supply
Connector
The circular connector on the shielded power cable (two 20 AWG
wires + shield) should be connected to the circular socket on the
panel, taking into consideration the polarity.
The shield must be connected to the ground (earth) of the power
supply.

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…software to open a TCP socket to the
DIAMOND E-1000 Series.
Connection
Requirements
Any TCP client software or firmware can communicate with the
E-1000 Series. However, only one socket to port 5000 is allowed at
this time. Simply open a socket to the IP address of the…

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

2011-Diode-Laser-Modules-and-Pattern-Generators-Catalog.pdf

…time delay and remote interlock socket), is
CE-marked and meets appropriate UL, CSA, and EN
requirements.
This compact (120 x 76 x 48 mm) power supply can
be connected to any 90-130 or 180-260 VAC 50/60 Hz
supply.There is an IEC 320 input socket and a 1.8 m
detachable…

COHR VLM DS 1117 2.pdf

COHR VLM DS 1117 2.pdf

…connected to any 90-260 VAC 50/60 Hz supply. There is an IEC 320
input socket and a 1.8 m detachable line cord with plug provided.
The 1.8 m output cable is terminated with an easy connect/disconnect
jack socket
Purchase separately the 3.5 mm Plug to then add to your laser power…

ModeMaster PC User Manual

ModeMaster PC User Manual

…the provided USB cable.
3. Connect Control/Interface Console to power socket using the
provided power supply.
4. Attach AC power cord from rear of ModeMaster PC
Control/Interface Console to AC power socket. ModeMaster
PC senses power and automatically adjusts to use any AC…

COHR VLM DS 0819 2.pdf

COHR VLM DS 0819 2.pdf

…connected
to any 90-260 VAC 50/60 Hz supply. There is an IEC 320 input socket and a 1.8 m
detachable line cord with plug provided. The 1.8 m output cable is terminated with
an easy connect/disconnect jack socket.
Purchase separately the 3.5 mm Plug to then add to your laser power…

Book.book

Book.book

…procedure described for the
optional heat sink. The laser system also includes modified M4
mounting hardware.
NOTICE!
Standard M4 socket head screws do not provide sufficient
clearance for mounting holes.
Power Supply The CUBE laser system includes a power supply, which…

Picosecond laser

Picosecond laser

HYPER RAPID 24 of 27
Figure 8: emergency stop socket (female)
Pin Description
1 Relay contact is internally closed with pin 2, as long as emergency switch (front side) is
not activated.
2 refer to pin 1
3 Relay contact is internally closed with pin 4, as long as…

Paladin Advanced Preinstallation.book

Paladin Advanced Preinstallation.book

…NALCOTM
460-CCL105" on page A-1). The system needs approximately
3 liters (1 gallon).
4. Connect the ventilation plug to the drain socket on the lower
center of the front panel. Keep a towel close at hand to dry any
spills (see Figure 3-7). Put NALCOTM into the funnel.

book.book

book.book

…the set screw too far, or it could fall out.
If you need to replace the set screw, purchase using these specifications:
Set Screw, Hex Socket Drive, 2-56 x 0.09375" (3.32") L,
Stainless Steel 316, Cup Point
2. Slide the head off.
3. Replace with the selected head.
4.…

COHR OBIS CellX DS 0117 3.pdf

COHR OBIS CellX DS 0117 3.pdf

…mm
(5.79 in.)
4.0 mm (0.16 in.)
10.0 mm
(0.39 in.)
4X Ø 4.8 mm (0.19 in.) Thru All
Mounting Holes for M4 or #8
Socket Head Cap Screws
MECHANICAL SPECIFICATIONS
OBIS CellX
OBIS CellX Datasheet
MECHANICAL AND ENVIRONMENTAL
SPECIFICATIONS OBIS…

00 LMT Pre.book

00 LMT Pre.book

Site Preparation
1 - 7
COHERENT MAKES NO RECOMMENDATION FOR
PLUGS OR SOCKETS FOR ANY CONNECTION, AND
ACCEPTS NO RESPONSIBILITY OR LIABILITY WHATSOEVER FOR THE ELECTRICAL CONNECTION
BETWEEN THE LMC SYSTEM COMPONENTS AND
PRIMARY ELECTRICAL POWER SUPPLY. IT IS SOLELY