Search Results

Refine
1 - 12 of 45 Products for 'Status Indicator' Page 1 of 4 |

Status Indicator

OBIS LX/LS Single Laser Remote

OBIS LX/LS Single Laser Remote

status indicators and offers CDRH-compliant safety features. Contact Us About This Product Close PRICE HERE Full Feature Laser Remote and Power Supply
* The OBIS Remote offers CDRH compliant safety features such as key switch and interlock
* The OBIS Remote shows four separate status indicators
*…

OBIS LX/LS Laser Box

OBIS LX/LS Laser Box

…LX/LS Laser Box
* Modulation inputs for analog and digital control
* USB and RS-232 interface for additional control from host computer
* Status indicators for each laser
* External power supply
* Laser safety features such as key switch, interlock OBIS Laser Box Part Numbers Description Part Number…

COHERENT CORPORATE OVERVIEW

COHERENT CORPORATE OVERVIEW

pg. 7 |
Top Panel Status Indicator - Easy-to-Read
Mode Color
Warm up
Error
Laser Emission
Standby
Integrated computer for control, diagnostics, and status

Book.book

Book.book

Status
The Laser Emission Status screen indicates the current state of laser
output and system status. The central indicator also shows Standby,
CDRH Delay, and System Faults. The ON and OFF buttons are used
to toggle laser emission.
Laser Mode Status The Laser Mode Status

COHR OBIS LG DS 0118 8.pdf

COHR OBIS LG DS 0118 8.pdf


Indicator
Output Beam
Shutter
Control
0.126 ±0.0005 X 0.188
Deep Slot and Hole
for Alignment Pins
M4-0.7 X 4.0 mm Deep Mounting Holes (4X)
Mounting Holes
for 3 mm or No. 6 Screws
(4X)
USB Control Fan
Status
Indicators
Heat…

EnergyMax-USB/RS User Manual

EnergyMax-USB/RS User Manual

…software (p. 4-14)
LED Status
Indicator
A blue LED light is contained within the EnergyMax-USB and
EnergyMax-RS connectors to provide health-and-status information.
Table 4-1. EnergyMax-USB/RS LED Light Conditions
LED Light Condition Status
No light visible If the…

ModeMaster PC User Manual

ModeMaster PC User Manual

…Special Weights - Indicates the current Special Weights Status.
Special Weights will be indicated by an "On" condition and Normal
Weighting will be indicated by an "Off" condition.
Alignment Status - Indicates the current alignment status. "OK"
indicates that the current Scan…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual


4 - 3
Status LED
Indicators
There are three Status LEDs on
the front panel:
· Laser Ready
· Laser Fault
· Power On
The following table lists all the possible states of the controller
Status LEDs.
For information on the laser Status LED, refer to…

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…bottom left section is devoted to visual diagnostic indicators.
Faults are kept apart from interlock and general system status indicators. Serious faults are indicated in RED and warnings are indicated in yellow. Temperature is indicated in the center of the applet.
RF power is shown…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…mm
(4.53 in.)
125.0 mm
(4.92 in.)
Emission
Indicator
Output Beam
Shutter Control
Mounting Holes
for 3 mm or No. 4 Screws
(4X)
USB Control Fan
Status
Indicators
Heat Sink Surface
Laser Head
Top View
Side View

COHR OBIS SingleLaserRemote DS 0317 1.pdf

COHR OBIS SingleLaserRemote DS 0317 1.pdf

…USB 2.0, Mini B
Host Computer Remote Control via RS-2321 RS-232 115.2K, 8N1
Interlock Yes, included with shorting wire
Laser Status Indicators Yes
Analog Modulation Input SMB, 50 Ohm OR 2KOhm, 0 to 5V
Digital Modulation Input2 SMB, 50 Ohm, 0 to 3V
Warm-up Time (minutes)…

OBIS-Single-Laser-Remote-Data-Sheet.pdf

OBIS-Single-Laser-Remote-Data-Sheet.pdf

…2.0, Mini B
Host Computer Remote Control via RS-2321 RS-232 115.2K, 8N1
Interlock Yes, included with shorting wire
Laser Status Indicators Yes
Analog Modulation Input SMB, 50 Ohm OR 2KOhm, 0 to 5V
Digital Modulation Input2 SMB, 50 Ohm, 0 to 3V
Warm-up Time…