Search Results

Refine
1 - 12 of 15 Products for 'Taper' Page 1 of 2 |

Taper

Ahead the New Glass Cutting COHR Rofin Whitepaper.pdf

Ahead the New Glass Cutting COHR Rofin Whitepaper.pdf

…cutting. In addition to limited cutting speed and some edge roughness, the
other limitation of topside scribing using an ultrafast laser is a taper always remains on the scribe or
hole, usually in the 8° to 12° range.
Within ultrafast lasers, cut quality using a femtosecond laser has…

SmartCut+ and SmartWeld+ Application Packages for StarFiber Series

SmartCut+ and SmartWeld+ Application Packages for StarFiber Series

…It combines the benefits of a precision processing head with the flexibility of a scanner. It allows cutting complex microstructures with reduced taper and at high speed, particularly when integrated on-the-fly. This makes it a cost-effective solution which delivers reduced cycle times and which is…

Single emitter diode lasers

Single emitter diode lasers

--> Single Emitter Diode Lasers Packaged single emitter devices. Contact Us About This Product Close PRICE HERE High Power Single Emitters for Pumping and Direct-Diode Applications Packaged single emitter diodes, including industry-standard c-mounts, based on Coherent’s industry-leading…

StarCut Tube Laser Cutting Machine | High-Precision Laser Tube Cutting System

StarCut Tube Laser Cutting Machine | High-Precision Laser Tube Cutting System

--> StarCut Tube Machine The StarCut Tube systems are 3/4-axes CNC laser cutting solutions for fully-automated cutting of tube and flat material, especially for medical instruments and implants like stents and other high-precision parts. Frequently, the systems allow reducing numerous mechanical…

Diode Lasers

Diode Lasers

…powers up to multiple kilowatts. Single Emitter Diode Lasers Single Emitter Diode Lasers Bare chips, single emitters and laser bars based on tapered, broad-area or customized designs from 1.85 µm to >2 µm for pumping, medical, materials processing, spectroscopy, metrology and illumination…

07(IK14-10)p.53-57.fm

07(IK14-10)p.53-57.fm

…large taper
angles between entrance and exit holes are typically
obtained in 193 nm excimer laser via drilling using 100 µm
glass samples. (This natural depth of focus effect is reduced
in the 50 and 30 µm thickness samples, as expected.) We
found that the taper angle can…

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

Information Display Magazine September/October 2017, Vol. 33, No. 5 issue

…ablated
chips fall out of the material interaction zone
due to gravity. Scribes or cuts of virtually any
edge profile, including tapered slots, holes,
trenches, bevels, and chamfers, can be generated by moving the beam focus up through the
substrate and then along it to…

The PCB Magazine, November 2015

The PCB Magazine, November 2015

…wavelength.
Clean, round, symmetric vias were successfully produced in all the thicknesses tested using a total of 700 pulses or less. Hole taper was
seen in the higher thicknesses, but sequential
drilling from both sides of the glass reduced this
effect substantially. This is…

Microsoft Word - COHR HeavyMetalPipeCutting WP 0519

Microsoft Word - COHR HeavyMetalPipeCutting WP 0519

…slots is tapered where the outer width is narrower
than the width at the inner tube wall (Figure 4). While mechanical tooling can often cut straight
slots competitively with lasers, the keystone slots are another matter. Milling tools can only
achieve a limited range of tapers, and…

Industrial Laser Solutions - September/October 2015

Industrial Laser Solutions - September/October 2015

…r t
Clean, round, symmetric vias were successfully produced in all the thicknesses
tested using a total of 700 pulses or less.
Hole taper was seen in the higher thicknesses, but sequential drilling from both
sides of the glass reduced this effect substantially. This is relatively…

Industrial Photonics - October 2017

Industrial Photonics - October 2017

…is tapered so that the outer width
is narrower than the width at the inner
tube wall (Figure 4).
While mechanical tooling can often
cut straight slots competitively with lasers, the keystone slots are another matter. Milling tools can only achieve a
limited range of tapers,

Properties-of-Structured-Light-Application-Note.pdf

Properties-of-Structured-Light-Application-Note.pdf

…I (800) 527-3786 I (408) 764-4983 5
Application Note
Laser Line Straightness
Projected laser lines are rarely straight. Tapered ends or a
slightly S-shaped line can occur and are often indicators of
poor line straightness (see Figure 9). Depending on the…