Search Results

Refine
37 - 48 of 64 Products for 'Thread' Page 4 of 6 |

Thread

COHR OBISfamily DS 0719 2.pdf

COHR OBISfamily DS 0719 2.pdf

…SPECIFICATIONS
OBIS LX/LS
38 mm
(1.5 in.)
Status
Indicator
Safety
Shutter
Laser Exit Aperture
M6 X 0.75 Thread
2.54 mm Deep
OEM Label
Fan
USB
SDR
Power
40 mm
(1.57 in.)
19 mm
(0.75 in.)
15.5 mm

COHR OBISfamily DS 0119 3.pdf

COHR OBISfamily DS 0119 3.pdf

…SPECIFICATIONS
OBIS LX/LS
38 mm
(1.5 in.)
Status
Indicator
Safety
Shutter
Laser Exit Aperture
M6 X 0.75 Thread
2.54 mm Deep
OEM Label
Fan
USB
SDR
Power
40 mm
(1.57 in.)
19 mm
(0.75 in.)
15.5 mm

Picosecond laser

Picosecond laser

…free of condensation. For the environmental conditions please refer to section "Ambient condition" on page 6.
l
Adequate table with thread holes (M6) in order to position
and fix the laser head. Refer to section "Footprint, Pedestals" on page 15.
l
Provide adequate…

LaserCam-HR II User Manual

LaserCam-HR II User Manual

Setup
3 - 3
Mounting the
Camera
LaserCam-HR II can be mounted in any rotational position with a
1/4
-20 or M6 threaded mounting post. Figure B-1 (p. B-2) shows the
mounting post location. Alignment marks permit rotation of the
camera and alignment with the…

COHR SapphireSF DS 0719 3.pdf

COHR SapphireSF DS 0719 3.pdf


66.0 mm
(2.60 in.)
14.9 mm
(0.59 in.)
38.1 mm
(1.5 in.)
33.3 mm
(1.31 in.)
4 Spacers with Tapped
Thread M3 3.5 mm (0.14 in.)
DC Power Connector
Molex Micro Fit 3.0 10 Positions
Analog Interface
26 Pin IDC Connector
Male

COHR SapphireSF DS 0819 1.pdf

COHR SapphireSF DS 0819 1.pdf


66.0 mm
(2.60 in.)
14.9 mm
(0.59 in.)
38.1 mm
(1.5 in.)
33.3 mm
(1.31 in.)
4 Spacers with Tapped
Thread M3 3.5 mm (0.14 in.)
DC Power Connector
Molex Micro Fit 3.0 10 Positions
Analog Interface
26 Pin IDC Connector
Male

COHR Air-CooledThermopileSensors DB25 DS 0819 2.pdf

COHR Air-CooledThermopileSensors DB25 DS 0819 2.pdf

…(7.44-10.2 in.) 3/8-16 UNC
Female Mounting Threads
Ø19 mm
(0.75 in.)
Ø151 mm
(5.95 in.)
Note: Detector Surface
is 32.3 mm (1.27 in.) below
front face of aperture plate
3/8-16 UNC
Female Mounting
Threads
Ø50 mm
(1.97 in.)
Ø151 mm…

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

…- Remove Assist Gas Tube
4. Once the nozzle assembly is completely removed you need to remove the optic window from the assembly and
clean it on both sides. The optic window is held in place with a threaded ring nut. Note the two holes in the top
of the nut. See Figure 4.

CUBE family DSrevD

CUBE family DSrevD

…12 mm
(0.5 in.)
2 Places
43.5 mm
(1.7 in.)
2 Places
32 mm
(1.3 in.)
35.9 mm
(1.4 in.)
4X #4-40 Threads
2 Places, Near and Far Side
Top
View
Side
View Rear View
Front View
OBIS 6-Laser Remote
Power Supply

COHR Fan-CooledThermopileSensors DB25 DS 0719 1.pdf

COHR Fan-CooledThermopileSensors DB25 DS 0719 1.pdf

…1098480 10984721 10985091 1098417
1 C24 Quick Ship program: eligible for next business day shipment.
1/4-20 UNC
Female Mounting
Threads
3 Places
Ø50 mm
(1.97 in.)
for PM200F-50
Ø19 mm
(0.76 in.)
for PM200F-19
114 mm
(4.49 in.)
102…

PowerMax-USB-RS-Sensors-Product-Guide.pdf

PowerMax-USB-RS-Sensors-Product-Guide.pdf

…& Performance · www.Coherent.com · LMC.sales@coherent.com
The following fiber-optic adapters can be mounted directly onto the 3/4-32 threads
on the front of LM-3 and LM-10 sensors.These fiber adapters can also be used with
our 1.035-40M adapter ring to fit on the LM-45 sensor.…

Verdi preinstall.book

Verdi preinstall.book

…item 9) to
connect the riser/heat sink to the chiller (Figure 1-6). Apply
teflon tape to the hardware threads and install the washers from
the installation kit over the threads when connecting the stainless steel ferrule to the riser/heat sink. Check the system for
leaks.
4.…