Search Results

37 - 48 of 61 Products for 'Thread' Page 4 of 6 |

Thread

COHR SapphireSF DS 0819 1.pdf

COHR SapphireSF DS 0819 1.pdf


66.0 mm
(2.60 in.)
14.9 mm
(0.59 in.)
38.1 mm
(1.5 in.)
33.3 mm
(1.31 in.)
4 Spacers with Tapped
Thread M3 3.5 mm (0.14 in.)
DC Power Connector
Molex Micro Fit 3.0 10 Positions
Analog Interface
26 Pin IDC Connector
Male

00 M5C Pre Install.book

00 M5C Pre Install.book

…level
nozzle
gap See nozzle offset
nozzle
offset Distance between the cutting nozzle and the workpiece.
NPT National pipe thread
OD Outside diameter, or Optical density; see optical density
OEM Original equipment manufacturer
optical
density Logarithm to…

COHR Air-CooledThermopileSensors DB25 DS 0819 2.pdf

COHR Air-CooledThermopileSensors DB25 DS 0819 2.pdf

…(7.44-10.2 in.) 3/8-16 UNC
Female Mounting Threads
Ø19 mm
(0.75 in.)
Ø151 mm
(5.95 in.)
Note: Detector Surface
is 32.3 mm (1.27 in.) below
front face of aperture plate
3/8-16 UNC
Female Mounting
Threads
Ø50 mm
(1.97 in.)
Ø151 mm…

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

Microsoft Word - LMT Lens Optics Cleaning Procedure COHR.docx

…- Remove Assist Gas Tube
4. Once the nozzle assembly is completely removed you need to remove the optic window from the assembly and
clean it on both sides. The optic window is held in place with a threaded ring nut. Note the two holes in the top
of the nut. See Figure 4.

CUBE family DSrevD

CUBE family DSrevD

…12 mm
(0.5 in.)
2 Places
43.5 mm
(1.7 in.)
2 Places
32 mm
(1.3 in.)
35.9 mm
(1.4 in.)
4X #4-40 Threads
2 Places, Near and Far Side
Top
View
Side
View Rear View
Front View
OBIS 6-Laser Remote
Power Supply

COHR Fan-CooledThermopileSensors DB25 DS 0719 1.pdf

COHR Fan-CooledThermopileSensors DB25 DS 0719 1.pdf

…1098480 10984721 10985091 1098417
1 C24 Quick Ship program: eligible for next business day shipment.
1/4-20 UNC
Female Mounting
Threads
3 Places
Ø50 mm
(1.97 in.)
for PM200F-50
Ø19 mm
(0.76 in.)
for PM200F-19
114 mm
(4.49 in.)
102…

COHR Fan-CooledThermopileSensors DB25 DS 0919 2.pdf

COHR Fan-CooledThermopileSensors DB25 DS 0919 2.pdf

…1098480 10984721 10985091 1098417
1 C24 Quick Ship program: eligible for next business day shipment.
1/4-20 UNC
Female Mounting
Threads
3 Places
Ø50 mm
(1.97 in.)
for PM200F-50
Ø19 mm
(0.76 in.)
for PM200F-19
114 mm
(4.49 in.)
102…

PowerMax-USB-RS-Sensors-Product-Guide.pdf

PowerMax-USB-RS-Sensors-Product-Guide.pdf

…& Performance · www.Coherent.com · LMC.sales@coherent.com
The following fiber-optic adapters can be mounted directly onto the 3/4-32 threads
on the front of LM-3 and LM-10 sensors.These fiber adapters can also be used with
our 1.035-40M adapter ring to fit on the LM-45 sensor.…

Verdi preinstall.book

Verdi preinstall.book

…item 9) to
connect the riser/heat sink to the chiller (Figure 1-6). Apply
teflon tape to the hardware threads and install the washers from
the installation kit over the threads when connecting the stainless steel ferrule to the riser/heat sink. Check the system for
leaks.
4.…

LabMax-Pro-Data-Sheet FORMFIRST.pdf

LabMax-Pro-Data-Sheet FORMFIRST.pdf

4X No.4-40 Threads
2 PL, Near and Far Side
104.9 mm
(4.1 in.)
32 mm
(1.3 in.)
34.5 mm
(1.4 in.)
105.6 mm
(4.2 in.)
31 mm
(1.2 in.)
2 PL
43.5 mm
(1.7 in.)
2 PL
9.2 mm
(0.4 in.)
2 PL
13.7 mm
(0.5 in.)…

Biosafety Level 3 setup for multiphoton microscopy in vivo

Biosafety Level 3 setup for multiphoton microscopy in vivo

…probe as well as an opening for the
objective. (d) Behind the objective an optical quartz window is placed and tightened into place using a threaded
42mm metal ring that compresses a 38mm O-ring. To ensure a seal of the BSC at the level of the objective we
connected the objective…

COHR OBIS SingleLaserRemote DS 0317 1.pdf

COHR OBIS SingleLaserRemote DS 0317 1.pdf

…mm
(0.5 in.)
2 Places
12 mm
(0.5 in.)
2 Places
43.5 mm
(1.7 in.)
2 Places
32 mm
(1.3 in.)
35.9 mm
(1.4 in.)
4X #4-40 Threads
2 Places, Near and Far Side
Top
View
Side
View
Rear View
Front View

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions