Search Results

1 - 12 of 33 Products for 'Water Chiller Manual' Page 1 of 3 |

Water Chiller Manual

00 Laser Cooling.book

00 Laser Cooling.book


Symbols Used in This Manual and on the Laser System .................................................v
Introduction ......................................................................................................................1
Function of Cooling Water

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

Preinstallation Manual Astrella Ultrafast Amplifier Laser System

…Operator's Manuals for additional information.
Water Chiller The closed-loop water chiller dissipates the heat generated by the
system and stabilizes the Vitara, Revolution, and amplifier cavity.
The temperature is set to 20 °C and should not be changed. Refer to
the chiller

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

Astrella Ultrafast Amplifier Laser System Preinstallation Manual

…Operator's Manuals for additional information.
Water Chiller The closed-loop water chiller dissipates the heat generated by the
system and stabilizes the Vitara, Revolution, and amplifier cavity.
The temperature is set to 20 °C and should not be changed. Refer to
the chiller

Picosecond laser

Picosecond laser

…- connecter for HV switch in the laser head
33 connecter for HV cable: no function
34 Desiccant cartridge
35 CPC connecter water out to chiller
36 Air outlet from fans
Interlock connecter
Shutter
The IL/Shutter connector is located at the rear side of the

Verdi preinstall.book

Verdi preinstall.book

chiller in the operating position. Fill and prepare
the chiller in accordance with the chiller user's manual.
3. Cut the user-supplied cooling water lines to the appropriate
lengths and use the water line hardware (Figure 1-1, item 9) to
connect the riser/heat sink to the chiller

Laser Marking Workstations

Laser Marking Workstations

…module (oscillating table configuration only)
* Digital readout, motorized or programmable upgrade of Z-Axis
* Refrigerated recirculating water chiller for all LME-RM versions (laser dependent)
* Automated Pick ‘N Place parts handling
* Custom Motion Control ability
* Fume extractor, available…

Libra PreInstallation.book

Libra PreInstallation.book


Table 3-3. Water Chiller Specifications
PARAMETER REQUIREMENT
Flow Rate 16.7 liters/minute (4.4 gallons/minute)
Capacity1 8 liters (2 gallons)
[1]Only distilled water may be used to fill-up the water chiller. Refer to the
Evolution Operator's manual or contact Coherent…

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

Preinstallation Manual Paladin Advanced Mode Locked UV Laser System

…unit. Slowly pour in NALCO TM until the
coolant level reaches the "Max." on the fill indicator.
Figure 3-7. Chiller Water Connections
Chiller Water Connections for
Laser Head Water Connections
PaladinTM 8W/10W
Chiller Water Connections for
PaladinTM 16/24/35 W

00 E-1000 PreInst.book

00 E-1000 PreInst.book

…then turn the chiller on.
· Open the valve in the water return (drain) line.
· Slowly open the valve in the water supply line.
· With the water supply pressure and water line differential pressure in accordance with Table 1-2 on page 1-8 (in the operator's manual), check all…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

…valves, then turn the chiller on.
· Open the valve in the water return (drain) line.
· Slowly open the valve in the water supply line.
· With the water supply pressure and water line differential pressure in accordance with Table 1-2 in the operator's manual,
check all…

00 Legend Elite Preinstallation.book

00 Legend Elite Preinstallation.book

…Vitara Chiller
The Vitara chiller is a closed loop system and requires distilled water
only.
SDG Elite 100-240 VAC, 50-60 Hz 200 VA 1 A / 0.5 A
Compressor remote control negligible negligible negligible
Computer 2 A / 1 A
1Refer to the respective operator's manual for…

Vitara Preinstall.book

Vitara Preinstall.book


Altitude Sea level to 3000 m (10,000 ft)
Table 3-3. Water Chiller Specifications
PARAMETER REQUIREMENT
Flow Rate
1.0 to 1.5 liters/minute (0.2 to 0.4
gallons/minute)
Maximum Pressure 200 kPa (30 psi)
Operating Water Temperature 20 oC (69 °F)