Ask a Question
Coherent
Search Results
Refine

Result Type

1 - 12 of 73 Products for 'Water Cooling Verdi' Page 1 of 7 |

Water Cooling Verdi

Verdi preinstall.book

Verdi preinstall.book

…in close proximity to the laser. The main power disconnect switch shall be clearly marked as the disconnecting device for the laser, and shall be within easy reach of the operator. LASER HEAD AIR COOLED POWER SUPPLY UMBILICAL FACILITY POWER WATER LINES (if using Water Cooling) CHILLER FACILITY POWER

Verdi preinstall.book

Verdi preinstall.book

Verdi V-18 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective plastic…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-2/V-5/V-6 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet (if included) 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material…

Verdi preinstall.book

Verdi preinstall.book

…sink and chiller or chill plate can also be used. Refer to the paragraph titled, Installing the Laser Head, for additional information on removing waste heat from the laser head. LASER HEAD AIR COOLED POWER SUPPLY UMBILICAL FACILITY POWER WATER LINES (if using Water Cooling) CHILLER FACILITY POWER

Verdi preinstall.book

Verdi preinstall.book

Verdi V-8/V-10 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-8/V-10 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective…

Mira-Optima-900-F-Data-Sheet.pdf

Mira-Optima-900-F-Data-Sheet.pdf

…when crystal's cooling water is maintained at ±0.1°C. 8 1/e2 diameter (±0.2 mm) at exit port. 9 Full angle divergence (±0.3 mrad) at exit port. 10 Typical measured M2 value is 1.1 0.0 700 1.8 750 800 850 900 950 1000 Wavelength (nm) OutputPower(W) 10W Verdi pump 8W Verdi pump 5W Verdi pump 0.0 700…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-18 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective plastic…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-2/V-5/V-6 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet (if included) 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-18 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective plastic…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-2/V-5/V-6 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet (if included) 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material…

Verdi preinstall.book

Verdi preinstall.book

Verdi V-8/V-10 Laser Preinstallation Manual 4 1. Dowel holes (2) 2. Cooling water inlet and outlet 3. Laser head clamp screw holes (4) 4. Optical table clamp mounts (4) Figure 1-2. Riser/Heatsink 1. Laser head 2. Protective plastic cover retaining screws (3) 3. Protective material 4. Protective…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions