Ask a Question
Coherent

Search Results

Refine

Result Type

25 - 36 of 4410 Products for 'adjustment' Page 3 of 368 |
Related Categories: Str 660 | 405 Nm Laser | Stingray | Stingray Laser | Str-639

adjustment

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…key switch · Remote interlock · Remote control option via Analog, RS-232, or USB interface · Laser power adjustment and graphic display (optional) · Front panel control with laser power adjustment and status display (optional) · Status LEDs 196 mm (7.72 in.) 90 mm (3.54 in.) 164 mm (6.46 in.) 9.5 mm…

COHR LifeSciencesGuide0215revN 2lr.pdf

COHR LifeSciencesGuide0215revN 2lr.pdf

…key switch · Remote interlock · Remote control option via Analog, RS-232, or USB interface · Laser power adjustment and graphic display (optional) · Front panel control with laser power adjustment and status display (optional) · Status LEDs 196 mm (7.72 in.) 90 mm (3.54 in.) 164 mm (6.46 in.) 9.5 mm…

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

Lasers-for-Life-Sciences-Product-Guide FORMFIRST.pdf

…key switch · Remote interlock · Remote control option via Analog, RS-232, or USB interface · Laser power adjustment and graphic display (optional) · Front panel control with laser power adjustment and status display (optional) · Status LEDs 196 mm (7.72 in.) 90 mm (3.54 in.) 164 mm (6.46 in.) 9.5 mm…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

Converting a BioRay Laser to FC B - 7 3. Using the two alignment setscrews, adjust the fiber ferrule laterally relative to the BioRay laser beam. Continue this adjustment until the output power exiting the fiber is peaked (very bright) on the screen. 4. Put the photodiode sensor in front of the exit…

Coherent BioRay Operator's Manual

Coherent BioRay Operator's Manual

Converting a BioRay Laser to FC B - 7 3. Using the two alignment setscrews, adjust the fiber ferrule laterally relative to the BioRay laser beam. Continue this adjustment until the output power exiting the fiber is peaked (very bright) on the screen. 4. Put the photodiode sensor in front of the exit…

00 Cube.book

00 Cube.book

…laser system provides the ability to adjust the diode threshold level. The diode threshold adjustment is made to optimize pulse performance in regards to modulation depth or pulse repetition bandwidth. A secondary requirement for the threshold adjustment is to maintain specified modulation bandwidth…

Microsoft Word - MAN GPWRLN R01.doc

Microsoft Word - MAN GPWRLN R01.doc

…Panel of the Lasiris Green PowerLine laser Diode current (mA) = diode current monitor (mV) Power (mW) = Photodiode current monitor (mV) Power adjustment potentiometer ON/OFF switch Green LED (Power) Red LED (laser diode temperature) diode temperature too high or too low °laser off° DB-9 (external…

StingRay DS 0512 11 Final 05-09-12 .pdf

StingRay DS 0512 11 Final 05-09-12 .pdf

External Focus Adjustment Indicator Light Beam Exit Accessory Holder Ø19.05 mm (0.75 in.) Clamping Area Ø18.64 mm (0.73 in.) Ø18.64 mm (0.73 in.) 16.9 mm (0.7 in.) External Focus Adjustment Indicator LightBeam Exit Ø19.05 mm (0.75 in.) Clamping Area 36.5 mm (1.4 in.) Clamping Area 13.8 mm (0.5 in.)…

Coherent BioRay Fiber Coupling Accessory Quick Start Guide

Coherent BioRay Fiber Coupling Accessory Quick Start Guide

…1) adjust the two alignment setscrews and 2) move the collimating lens closer or further with the adjustment ring. (As a guideline, rotating the adjustment ring in the direction shown in the following photo will move the collimating lens closer to the laser diode.) Colliminating Lens Adjustment Ring…

Coherent BioRay Fiber-Ready Accessory Quick Start Guide

Coherent BioRay Fiber-Ready Accessory Quick Start Guide

…1) adjust the two alignment setscrews and 2) move the collimating lens closer or further with the adjustment ring. (As a guideline, rotating the adjustment ring in the direction shown in the following photo will move the collimating lens closer to the laser diode.) Colliminating Lens Adjustment Ring…

Book.book

Book.book

…error is displayed. (If working with a multiline laser, the best compromise is to adjust the wavelength setting to the arithmetic mean of the laser lines.) Turn the knurled adjustment ring on the lens assembly to adjust the lens spacing until the displayed error is less than 0.1. When the current…

Cover.p65

Cover.p65

…1 mW to 10 kW range. When an inappropriate range is selected, the D=-1 error code appears on the digital display. Adjust for ambient thermal effect for any attached probe. Adjust to account for mechanical offset in the analog meter. Activate and deactivate the PM500AD, or test the internal battery…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions