Search Results

37 - 48 of 58 Products for 'attenuator' Page 4 of 5 |

attenuator

LabMax-Pro Mobile for Android User Guide

LabMax-Pro Mobile for Android User Guide

…Applies an arbitrary gain factor to
all measurements. For example, if the sensor is downstream from a splitter or other device that attenuates the
actual laser beam, you can artificially inflate the
measurements so that they reflect the actual output of the
laser, rather…

LabMax-Pro Mobile for iOS User Guide

LabMax-Pro Mobile for iOS User Guide

…Applies an arbitrary gain factor to
all measurements. For example, if the sensor is downstream from a splitter or other device that attenuates the
actual laser beam, you can artificially inflate the
measurements so that they reflect the actual output of the
laser, rather…

FieldMaxII Family DS

FieldMaxII Family DS

…standard deviation
AVG Engage display averaging
Enter wavelength and engage wavelength compensation
ATTEN Enter attenuation factor and engage attenuation
AREA J/cm2 (fluence) W/cm2 (power density) J/cm2 (fluence)
W/cm2 (power density)
HOLD - Holds displayed values on…

COHR HyperRapid50 DS 0716 4.pdf

COHR HyperRapid50 DS 0716 4.pdf

…by one electrical trigger pulse.These 20 ns-bursts enhance the ablation rate in many materials and increase the process efficiency. The HYPER RAPID 50 uses an AOM as its process shutter which allows both on/off control and energy attenuation for each individual pulse. www.Coherent.com/HyperRapid50

10 Tips White Paper 1 rev9

10 Tips White Paper 1 rev9

…associated with camera based systems, some type of laser
beam attenution is always required whereas with knife edge systems, additional attenuation is
typically required at the higher power levels.
9 Attributes of a camera-based profiler.
Camera-based systems are particularly…

Photonics Spectra - July 2014

Photonics Spectra - July 2014

…have a fast response time
and thus can be useful for looking at pulse
shapes. However, they saturate above approximately 1 mW/cm2, so attenuating filters must be used when operating at higher
powers.
The main drawbacks of photodiodes
are that they have smaller active areas,…

PowerMax-USB-RS-Sensors-Product-Guide.pdf

PowerMax-USB-RS-Sensors-Product-Guide.pdf

…The measureable power varies significantly by wavelength. See the chart
on the next page.
A spectrally calibrated ND2 filter is used to attenuate the laser beam, thus
allowing for a higher average power measurement than is typically possible with a photodiode.The sensor works with CW…

HYPERRAPID100 DS 0414 5.pdf

HYPERRAPID100 DS 0414 5.pdf

…materials and increase the process efficiency. The HYPER RAPID 100 uses an AOM as its process shutter which allows both on/off control and energy attenuation for each individual pulse. High Power Industrial ps-Laser HYPER RAPID 100 Advantages: · High throughput at significantly reduced TCO · High…

COHR HyperRapid100 355-SW DS 0716 6.pdf

COHR HyperRapid100 355-SW DS 0716 6.pdf

…and increase the process efficiency. The HyperRapid 100 355-SW uses an AOM as its process shutter which allows both on/off control and energy attenuation for each individual pulse. High Power Industrial ps-Laser HyperRapid 100 355-SW Advantages: · 1064 nm, 532 nm and 355 nm outputs · High energy…

Laser Focus World - September 2015

Laser Focus World - September 2015

…44
L A S E R B E A M D I A G N O S T I C S continued
McCauley at Ophir-Spiricon explains,
the beam is first properly sized and attenuated using beam expanders and reducers, microscope objectives, and bulk
absorption filters. The resulting camera
signal is then analyzed for…

Book.book

Book.book

…compact size, it enables measurements at places
in optical set-ups where a standard detector head would not fit. With
its built-in attenuator, this device is ready to measure output power
from 0.5 W to 1 W.
LaserCheckTM Handheld Power Meter (RoHS) Part Number 1098293
NOTE:…

Quotation KML QGYYMMDD G  Institute Contact

Quotation KML QGYYMMDD G Institute Contact

…The flux
measured on the detector was 2.1x107 ph/sec, where in this case very thick, high loss Aluminum
thin film filters were used to attenuate the beam to avoid detector saturation and ensure an accurate
measurement.
In setting-up experiments using EUV light, the discrepancy…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions