Ask a Question
Coherent
Search Results
Refine

Result Type

13 - 24 of 39 Products for 'avia 355 operator manual' Page 2 of 4 |
Related Categories: Avia 355 355-x | Avia 355 X | Fap Manual | Avia

avia 355 operator manual

Avia preinstall.book

Avia preinstall.book

…and power supply in accordance with paragraphs titled, Installing the Laser Head, and Installing the Power Supply, complete the installation as follows: 1. Connect power supply to facility power. 2. Perform the cold start procedure located in Section Three, Operation, within the operator's manual.

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Operator's Manual vi Symbols Used in This Manual and on the Laser System This symbol is intended to alert the operator to the danger of exposure to hazardous visible laser radiation. This symbol is intended to emphasize the presence of important operating instructions.

Avia preinstall.book

Avia preinstall.book

…Preinstallation Manual 16 ECHO Mode The AVIA 355 provides an echo mode in which each character transmitted to the laser is echoed to the host. This feature can be turned on or off using the ECHO command (refer to Table 11). PROMPT Mode The AVIA 355 provides an prompt mode for terminal operation in…

Avia preinstall.book

Avia preinstall.book

…v Preface This manual contains preinstallation information for the AVIA 355/355-X Diode-Pumped Laser. Read the operator's manual carefully before operating the laser for the first time. Special attention should be given to Section One, Laser Safety, within the operator's manual that describes safety…

Avia preinstall.book

Avia preinstall.book

…v Preface This manual contains preinstallation information for the AVIA 355/355-X Diode-Pumped Laser. Read the operator's manual carefully before operating the laser for the first time. Special attention should be given to Section One, Laser Safety, within the operator's manual that describes safety…

Avia preinstall.book

Avia preinstall.book

…6. BNC Connectors DESCRIPTION FUNCTION Pulse Trigger In The rising edge TTL input will trigger a laser pulse (See Section Three, Operation, within the operator's manual for details). Note that this is an alternate to DB 25 pins 20 and 21 Pulse Sync Out TTL low output signal synchronous with the…

Avia preinstall.book

Avia preinstall.book

…6. BNC Connectors DESCRIPTION FUNCTION Pulse Trigger In The rising edge TTL input will trigger a laser pulse (See Section Three, Operation, within the operator's manual for details). Note that this is an alternate to DB 25 pins 20 and 21 Pulse Sync Out TTL low output signal synchronous with the…

Avia preinstall.book

Avia preinstall.book

…6. BNC Connectors DESCRIPTION FUNCTION Pulse Trigger In The rising edge TTL input will trigger a laser pulse (See Section Three, Operation, within the operator's manual for details). Note that this is an alternate to DB 25 pins 20 and 21 Pulse Sync Out TTL low output signal synchronous with the…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Operator's Manual ii This document is copyrighted with all rights reserved. Under the copyright laws, this document may not be copied in whole or in part or reproduced in any other media without the express written permission of Coherent, Inc. Permitted copies must carry…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Operator's Manual ii This document is copyrighted with all rights reserved. Under the copyright laws, this document may not be copied in whole or in part or reproduced in any other media without the express written permission of Coherent, Inc. Permitted copies must carry…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Operator's Manual ii This document is copyrighted with all rights reserved. Under the copyright laws, this document may not be copied in whole or in part or reproduced in any other media without the express written permission of Coherent, Inc. Permitted copies must carry…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 26 PRINT LASER ROD SERVO STATUS ?LRSS Returns the status of the laser rod temperature servo: 0 if the servo is OPEN. 1 if the servo is LOCKED. 2 if the servo is SEEKING. 3 if the servo has a FAULT. PRINT LASER ROD SET TEMP ?LRST Returns laser rod set…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions