Ask a Question
Coherent
Search Results
37 - 48 of 94 Products for 'avia 355 x' Page 4 of 8 |

avia 355 x

Avia preinstall.book

Avia preinstall.book

…PRINT UV POWER ?UP Returns the calibrated output UV average power in watts, or the word "External" if the system is in external trigger mode. PRINT X MOTOR POSITION ?MX Returns the X motor position for the crystal shifter X motor. Table 12. RS-232 Queries (Continued) QUERIES RETURNED INFORMATION

Avia preinstall.book

Avia preinstall.book

…PRINT UV POWER ?UP Returns the calibrated output UV average power in watts, or the word "External" if the system is in external trigger mode. PRINT X MOTOR POSITION ?MX Returns the X motor position for the crystal shifter X motor. Table 12. RS-232 Queries (Continued) QUERIES RETURNED INFORMATION

Avia preinstall.book

Avia preinstall.book

…PRINT UV POWER ?UP Returns the calibrated output UV average power in watts, or the word "External" if the system is in external trigger mode. PRINT X MOTOR POSITION ?MX Returns the X motor position for the crystal shifter X motor. Table 12. RS-232 Queries (Continued) QUERIES RETURNED INFORMATION

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 10 Table 4. EXTERNAL INTERLOCK/CHILLER Connector Pinouts THIS CONNECTOR IS A DA-15 PIN FEMALE (PLUG WITH SOCKETS) CONNECTOR. PIN DESCRIPTION FUNCTION 1 Emission lamp relay contact Output signal (pins 1 and 2) used to determine the Laser Emission Lamp…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 18 Setting the Baud Rate The baud rate of the 9-pin RS-232 port can be changed by means of the BAUDRATE=NNN command described in Table 11. After the baud rate is changed, the new setting will be used until it is changed (even if the system power is…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 20 PULSE MODE=n PM=n Sets the pulse mode. n = 0 in continuous mode. n = 1 is burst mode. n = 2 is CW alignment mode. REPRATE=nnnnnn RR=nnnnnn Sets the repetition rate in Hz. Allowable values: 3 to 300000 Hz. RESET SYSTEM=1 RESET=1 Stops the internal…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 22 Table 12. RS-232 Queries QUERIES RETURNED INFORMATION PRINT AVG CURRENT AND DELTA ?ACAD Prints the average diode current and the current difference between diode 1 and diode 2. PRINT BASEPLATE TEMP ?BT Returns laser head baseplate measured…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 10 Table 4. EXTERNAL INTERLOCK/CHILLER Connector Pinouts THIS CONNECTOR IS A DA-15 PIN FEMALE (PLUG WITH SOCKETS) CONNECTOR. PIN DESCRIPTION FUNCTION 1 Emission lamp relay contact Output signal (pins 1 and 2) used to determine the Laser Emission Lamp…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 18 Setting the Baud Rate The baud rate of the 9-pin RS-232 port can be changed by means of the BAUDRATE=NNN command described in Table 11. After the baud rate is changed, the new setting will be used until it is changed (even if the system power is…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 20 PULSE MODE=n PM=n Sets the pulse mode. n = 0 in continuous mode. n = 1 is burst mode. n = 2 is CW alignment mode. REPRATE=nnnnnn RR=nnnnnn Sets the repetition rate in Hz. Allowable values: 3 to 300000 Hz. RESET SYSTEM=1 RESET=1 Stops the internal…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 22 Table 12. RS-232 Queries QUERIES RETURNED INFORMATION PRINT AVG CURRENT AND DELTA ?ACAD Prints the average diode current and the current difference between diode 1 and diode 2. PRINT BASEPLATE TEMP ?BT Returns laser head baseplate measured…

Avia preinstall.book

Avia preinstall.book

AVIA 355/AVIA 355-X Laser Preinstallation Manual 10 Table 4. EXTERNAL INTERLOCK/CHILLER Connector Pinouts THIS CONNECTOR IS A DA-15 PIN FEMALE (PLUG WITH SOCKETS) CONNECTOR. PIN DESCRIPTION FUNCTION 1 Emission lamp relay contact Output signal (pins 1 and 2) used to determine the Laser Emission Lamp…

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions