Ask a Question
Coherent
Search Results
Refine
1 - 12 of 38 Products for 'beam dump' Page 1 of 4 |

beam dump

Fiber-to-Fiber Optic Switch

Fiber-to-Fiber Optic Switch

Fiber-to-Fiber Optic Switch The Fiber to Fiber Optic Switch (FFS) is built as a stand-alone unit sealed with a beam dump. Contact Us About This Product close PRICE HERE With the FFS, one laser source can be time or energy shared between several fiber optic cables. The FFS has one fiber input and up…

Coherent Whitepaper - Astrella Tisch Sphere FINAL.pdf

Coherent Whitepaper - Astrella Tisch Sphere FINAL.pdf

…power is required for the d-scan measurement head, so beamsplitters are used to sample the watt-level (~1 mJ @ 1 kHz) beam from the hollow fiber. The beam entering the beam dump would in general be available for experiments. The Coherent Astrella is an example of the latest generation of one-box…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

00 E-250 Pre.book

00 E-250 Pre.book

…· Blade detection for closed position. · RTD temperature sensors on blade and beam dump · Adjustable (635 nm diode pointer. (X-Y,tip-tilt,focus) · Optical Output Power: 0.5 to 1.0 mW · Wavelength: 635 +/- 10 nm · Beam Diameter: 3 mm · Divergence: < 2 mrad Simmer Circuit The simmer circuit applies…

00 E-250 Pre.book

00 E-250 Pre.book

…· Blade detection for closed position. · RTD temperature sensors on blade and beam dump · Adjustable (635 nm diode pointer. (X-Y,tip-tilt,focus) · Optical Output Power: 0.5 to 1.0 mW · Wavelength: 635 +/- 10 nm · Beam Diameter: 3 mm · Divergence: < 2 mrad Simmer Circuit The simmer circuit applies…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

00 E-250 Pre.book

00 E-250 Pre.book

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

00 E-250 Pre.book

00 E-250 Pre.book

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

00 E-250 Pre.book

00 E-250 Pre.book

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

beam. The red laser pointer beam is factory aligned with the main beam. The beam dump temperature is continuously monitored. A laser system temperature fault will occur if the beam dump temperature exceeds a safe operating level which could occur if there is no or low coolant flow to the beam dump.

Powered by Site Search powered by SLI Systems

Call 1-800-227-8840


Outside the U.S. 1-408-764-4983

Coherent has locations across the globe that are available to provide support for any product, service or inquiry.

Visit our Contact Page to connect with any of our global sites.


Corporate Headquarters
Coherent Inc.
5100 Patrick Henry Drive
Santa Clara, CA 95054 USA

email: tech.sales@coherent.com

Send Us a Message

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions