Ask a Question
Coherent
Search Results
13 - 24 of 565 Products for 'beam scan' Page 2 of 48 |

beam scan

ModeMaster PC User Manual

ModeMaster PC User Manual

…dot symbol within the small circle symbol (adjusts the scan head so the input beam is parallel with the scan head optical axis) and the dot and circle both to the center of the alignment target (adjusts scan head so the input beam is on its optical axis). 5. The micrometer adjustments controlling…

ModeMaster PC User Manual

ModeMaster PC User Manual

…dot symbol within the small circle symbol (adjusts the scan head so the input beam is parallel with the scan head optical axis) and the dot and circle both to the center of the alignment target (adjusts scan head so the input beam is on its optical axis). 5. The micrometer adjustments controlling…

ModeMaster PC User Manual

ModeMaster PC User Manual

…To minimize deconvolution errors in profiling the beam, the pinhole used to scan the beam must be 17% of the diameter of the beam being scanned. Therefore, the smaller pinhole is normally used for the Far Field profile that is scanned at the beam's focal plane. For cases in which the signal from the…

ModeMaster PC User Manual

ModeMaster PC User Manual

…To minimize deconvolution errors in profiling the beam, the pinhole used to scan the beam must be 17% of the diameter of the beam being scanned. Therefore, the smaller pinhole is normally used for the Far Field profile that is scanned at the beam's focal plane. For cases in which the signal from the…

ModeMaster PC User Manual

ModeMaster PC User Manual

…To minimize deconvolution errors in profiling the beam, the pinhole used to scan the beam must be 17% of the diameter of the beam being scanned. Therefore, the smaller pinhole is normally used for the Far Field profile that is scanned at the beam's focal plane. For cases in which the signal from the…

ModeMaster PC User Manual

ModeMaster PC User Manual

…window. Minimum = 1. Maximum = 100. F. Time delay. Controls horizontal location of scan within window. Minimum delay =1. Maximum delay = 1575. Figure 3-11. Beam Profiling in ModeMaster PC Input Beam Ref erence Plane Scan Location Focal Plane Scan Location Rotating Drum Scan Head A B C D E F G H

ModeMaster PC User Manual

ModeMaster PC User Manual

…window. Minimum = 1. Maximum = 100. F. Time delay. Controls horizontal location of scan within window. Minimum delay =1. Maximum delay = 1575. Figure 3-11. Beam Profiling in ModeMaster PC Input Beam Ref erence Plane Scan Location Focal Plane Scan Location Rotating Drum Scan Head A B C D E F G H

ModeMaster PC User Manual

ModeMaster PC User Manual

…window. Minimum = 1. Maximum = 100. F. Time delay. Controls horizontal location of scan within window. Minimum delay =1. Maximum delay = 1575. Figure 3-11. Beam Profiling in ModeMaster PC Input Beam Ref erence Plane Scan Location Focal Plane Scan Location Rotating Drum Scan Head A B C D E F G H

ModeMaster PC User Manual

ModeMaster PC User Manual

…azimuth angle of ModeMaster PC scan head. B. Pinhole size being used to make the scan (10 or 50 µm for MM- 1, -1S, -2, -2S, -3, -3S, and 100 or 500 µm for MM-4, -5). C. Indicates this is the profile at the Reference Plane. D. Transverse pinhole profile of the beam scanned at the current azimuth axis…

ModeMaster PC User Manual

ModeMaster PC User Manual

…azimuth angle of ModeMaster PC scan head. B. Pinhole size being used to make the scan (10 or 50 µm for MM- 1, -1S, -2, -2S, -3, -3S, and 100 or 500 µm for MM-4, -5). C. Indicates this is the profile at the Reference Plane. D. Transverse pinhole profile of the beam scanned at the current azimuth axis…

ModeMaster PC User Manual

ModeMaster PC User Manual

…azimuth angle of ModeMaster PC scan head. B. Pinhole size being used to make the scan (10 or 50 µm for MM- 1, -1S, -2, -2S, -3, -3S, and 100 or 500 µm for MM-4, -5). C. Indicates this is the profile at the Reference Plane. D. Transverse pinhole profile of the beam scanned at the current azimuth axis…

ModeMaster PC User Manual

ModeMaster PC User Manual

…Normal Weighting. Q. Azimuth angle of ModeMaster PC Scan Head at the time the focus scan (unlike azimuth angle displayed on Alignment Screen, which is the current azimuth angle). A focus scan must be made before ModeMaster PC can display beam characteristics on the Propagation Plot screen. The…

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions