1 - 10 of 81 Search Results for bnc
|
|
|
1.
Off-the-shelf OEM Power Sensors (RoHS)
|
|
... Buy 1098334 PM10-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098343 PM10-19B OEM-style, broadband coating, BNC connector (RoHS) Buy 1098418 PM150-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098321 PM150-19B OEM-style ...
Related Searches: beamfinder | oem
|
|
|
|
|
2.
Small-Area BNC Terminated Energy Sensors
|
|
Small-Area BNC Terminated Energy Sensors Superior Reliability & Performance Lasers and Laser-based Systems Laser Measurement and Control Precision Optics Related Accessories Sensors include an integrated, fast pre-amplifier circuit, and are optimized for measuring low-energy, high repetition rate ...
Related Searches: j4-09
|
|
|
|
|
3.
Small-Area BNC Terminated Energy Sensors
|
|
Small-Area BNC Terminated Energy Sensors Sales Support: 1-800-343-4912 NEW! Smart Finder Tool Search by Sensors and/or Meters. -- select product type -- Find a Sensor Find a Meter Find a Meter and Sensor Sensors include an integrated, fast pre-amplifier circuit, and are optimized ...
Related Searches: j4-09 | j3s-10 | j3s | j3s10
|
|
|
|
|
5.
Off-the-shelf OEM Power Sensors (RoHS)
|
|
|
... Buy 1098334 PM10-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098343 PM10-19B OEM-style, broadband coating, BNC connector (RoHS) Buy 1098418 PM150-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098321 PM150-19B OEM-style ...
|
|
|
|
6.
Avia_266_Preinstallation
(PAGE 16 OF 38)
|
|
|
... . Do not exceed ±10 V across pin 8 and 9. Input current will be less than 13 mA. Note that there is another external enable input available at a BNC connector on the rear panel. Either driving pins 8 and 9 or the BNC will enable pulsing. See Table 6. This input is not active in Internal Front Panel Trigger ...
|
|
|
|
|
7.
LaserCam-HR-InGaAsUserManualRevAA
(PAGE 28 OF 42)
|
|
|
... beam diagnostic system to interface with pulsed lasers and transient optical events, including single shot lasers. Trigger In Trigger In uses the BNC connector labeled "TRIG IN" on the LaserCam-HR-InGaAs Trigger and Pass/Fail cable. This 5 VDC, TTL input--which is available on the rising or ...
|
|
|
|
|
8.
Avia_266_Preinstallation
(PAGE 17 OF 38)
|
|
|
... either through pins 24 and 25 or on the front panel, before diode current and pulsing can be again enabled. 25 Reset Fault Refer to pin 24. Table 6. BNC Connectors DESCRIPTION FUNCTION Pulse Trigger In The rising edge TTL input will trigger a laser pulse (See Section Three, Operation, within the operator ...
|
|
|
|
|
9.
Off-the-shelf OEM Power Sensors (RoHS)
|
|
|
... Buy 1098334 PM10-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098343 PM10-19B OEM-style, broadband coating, BNC connector (RoHS) Buy 1098418 PM150-19A OEM-style, amplified, broadband coating, 4-pin connector (RoHS) Buy 1098321 PM150-19B OEM-style ...
|
|
|
|
|
10.
Materialwiss
|
Best match in this PDF
|
All matches in this PDF
|
... oscillations in the recorded reflection and transmission spectra. Syncronisation of the ScanMatePro with the experiment was conveniently done via BNC trigger ports and the built-in control and data acquisition software package. 3 Results and Discussion Reflection and transmission spectra for s-polarized ...
Related Searches: fabry perot
|
|
Coherent Contact Information