bracket on Coherent inc.

What's your interest?

Shows & Conferences

Founded in 1966, Coherent, Inc. is a world leader in providing superior laser reliability and performance.

> Search

Search Coherent

Superior Reliability & Performance

1 - 10 of 62 Search Results for bracket

Search Suggestions: avia 355-20 | thermeq

1. AVIA355_20	Best match in this PDF \| All matches in this PDF
`...` 24.9 kg (55 lbs.) Umbilical Length 5m (15 ft.) Power Supply--Back Power Supply--Front Power Supply--Side Power Supply--Top 434.34 mm 17.10 in. Slide Bracket 4 PLCS Slide 2 PLCS 499.11 mm 19.65 in. Handle Feet Slide mounting location (Shown with slide, slide mounting brackets, and rack removed). 40.89 `...` Related Searches: avia 355-20 \| thermeq

2. Innova300C_fredmotofred_preinstallation (PAGE 22 OF 32)
`...` : 1. Move the power supply so that the rear panel extends approximately two to three inches beyond the table edge. 2. Remove the umbilical support bracket by loosening the two hex screws (using a 5/32 inch Allen wrench) that secure it to the backside of the power supply. Figure 4. Umbilical Connections `...` Related Searches: 300c fred

3. Diamond_Integrators_Guide_RevAA (PAGE 26 OF 56)
`...` feet which attach to the liquid chill plate. The GEM air cooled laser heads come equipped with tapped holes which accommodate optional mounting brackets. These brackets provide rigid mounting while allowing thermal expansion. For more information please refer to the appropriate section in the operator `...`

4. Innova300C_fredmotofred_preinstallation (PAGE 23 OF 32)
`...` on the rear of the power supply labelled HEAD CONTROL. Secure the mounting screws on the plug with a screwdriver. 8. Replace the umbilical support bracket. 9. Rotate the umbilical holder so that the umbilical will exit the rear of the power supply horizontally or at 45°. Make sure not to crimp or collapse `...` Related Searches: mount

5. Innova300C_fredmotofred_preinstallation (PAGE 24 OF 32)
`...` case. 7. Use a 9/64 inch and a 5/32 inch Allen wrench to remove the two screws from the power supply and the two screws from the umbilical support bracket, respectively, which will hold the umbilical connections cover in place. 8. Slide the umbilical connections cover over the umbilical holder and bracket `...`

6. Innova300C_fredmotofred_preinstallation (PAGE 25 OF 32)
`...` operating power to the heat exchanger and water level feedback to the power supply. A cable strain relief is provided on each end with an attached bracket and Phillips head screws.

7. Innova300C_fredmotofred_preinstallation (PAGE 28 OF 32)
`...` of the laser head. 4. Pull out slightly on the umbilical assembly to release it from its mount, and then push the umbilical downwards. 5. Rotate the bracket to align the four clearance holes on the bottom of the head. 6. Push the assembly firmly upwards until it seats in the new location (Figure 6) `...`

8. Innova300C_fredmotofred_preinstallation (PAGE 29 OF 32)
Preinstallation Guidelines and Installation Procedure 21 Rack Mount Slide Brackets The Innova 300C FreD / MotoFreD ion laser power supply can be mounted into a standard 48.26 cm (19.00 inches) equipment rack. Rack mount slide brackets for cabinet depths of approximately 76.20 cm (30.00 inches) are `...`

9. Innova300C_fredmotofred_preinstallation (PAGE 30 OF 32)
`...` no further adjustment. The correct wavelength must be selected on the remote control module for proper calibration. Figure 7. How to Mount Rack Brackets to an Equipment Rack Mounting EIA rail Bar nut # 10-32 screws Mounting EIA rail

10. AVIA_355-23_DS_final (PAGE 1 OF 2)
`...` mm (2.875 in.) 75.69 mm (2.98 in.) 16 mm (0.63 in.) 6.35 mm (0.25 in.) 21.59 mm (0.85 in.) Slide Mounting Location (Shown with Slide, Slide Mounting Brackets, and Rack Removed) Handle Rack Air Intake Rack Mount Bracket Feet MENU UP MENU DOWN MENU SELECT DIODES ON PULSE ON SHUTTER OPEN STANDBY AC ON `...`

Search Suggestions: avia 355-20 | thermeq

Page 1 2 3 4 5 6 7 of 7 | Next

Site Search by

Click the button below to send your comments about the website.