Search Results

1 - 12 of 80 Products for 'c series' Page 1 of 7 |
Related Categories: Cw Co2 Lasers | Cx-10 | Cx 10 | Cx-10lde | C70

c series

UW Series 09-19-14 .cdr

UW Series 09-19-14 .cdr

…T H E M A R K O F E X C E L L E N C E The UW Series of modular, standard workstations are available in UW-180, UW-180 Open-Frame, and UW-150 Rotary-table versions. Developed to address industry's requirement for a low-cost Class 1 laser marking solution, the UW Series workstations offer significant…

00 E-400 E-1000 Series Preinstall.book

00 E-400 E-1000 Series Preinstall.book

Diamond E-400 Series OEM Lasers Preinstallation Manual
36
b. RF Power Module
c. Interface Mounting Dimensions
Figure 25. E-400 & E-400i System Installation in OEM Equipment
(Dimensions in mm [inches] and Required Clearances) (Continued)
946.2 mm
[37.25 in.]…

Genesis Taipan HD Series Datasheet 2016.pdf

Genesis Taipan HD Series Datasheet 2016.pdf

…Diode Current (A) <32 <29 <33
Diode Voltage (V) 1.5 to 2.2
Cooling Requirements4 Active cooling required
Case Temperature (°C) 25 ±2
Humidity Non-condensing
Dimensions (L x W x H)
Laser Head 134.14 x 44 x 64.47 mm (5.28 x 1.73 x 2.54 in.)
Weight
Laser…

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

DIAMOND J-3 Series OEM Lasers Preinstallation Manual, Rev. AB

System Description
1 - 13
Figure 1-6. J-3 Series Dimensions (including clearance)
17.8 mm
[.70 in.]
111.8 mm
[4.40 in.]
635 mm
[25.0 in.]
MIN CLEARANCE
REQUIRED FOR
RF MODULE
REMOVAL
198.1 mm
[7.80 in.]
OUTPUT
APERTURE…

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

DIAMOND J-5 Series OEM Lasers Preinstallation Manual Rev AA

System Description
1 - 13
Figure 1-6. J-5 Series Dimensions (including clearance)
17.8 mm
[.70 in.]
111.8 mm
[4.40 in.]
1016 mm
[40.0 in.]
MIN CLEARANCE
REQUIRED FOR
RF MODULE
REMOVAL
227.6 mm
[8.96 in.]
4X M4X0.7 - 6H

Genesis-Taipan-Series

Genesis-Taipan-Series

…<32 <29, <32 <36, <40
Diode Voltage (V) 1.5 to 2.2
Cooling Requirements6 Active cooling required
Case Temperature (°C) 25 ±2
Humidity Non-condensing
Dimensions (L x W x H)
Laser Head 121 x 44 x 68 mm (4.75 x 1.73 x 2.68 in.)
Weight
Laser Head…

FAP-600-Series-Data-Sheet.pdf

FAP-600-Series-Data-Sheet.pdf


Thermal Specifications
Thermal Resistance (typical)(°C/W) 0.7 0.7 0.7
Case Operating Temperature (°C) -20 to 30 -20 to 30 -20 to 30
Case Storage Temperature (°C) -20 to 60 -20 to 60 -20 to 60
Recommended Heat Sink
Capacity (W) 100 100 100
Thermal Resistance (°C/W)…

Genesis-MX-IR-Series-MTM-OEM

Genesis-MX-IR-Series-MTM-OEM

GenesisTM MX IR Series MTM (OEM)
High-Power Optically Pumped Semiconductor Lasers (OPSL)
Coherent follows a policy of continuous product improvement. Specifications are subject to change without notice.
Coherent's scientific and industrial lasers are certified to comply with the…

Genesis-MX-Series-607-639-MTM-End-User

Genesis-MX-Series-607-639-MTM-End-User


CDRH Compliant Yes
Operating Voltage (VAC) 100 to 240
Frequency (Hz) 50 to 60
Power Consumption (W) 500
Ambient Temperature (°C)
Operating 10 to 40
Non-Operating -10 to 60
Relative Humidity6 (%) 5 to 95
CE Marking IEC 61010-1/EN 61010-1
Dimensions (L…

Genesis-MX-Series-607-639-STM

Genesis-MX-Series-607-639-STM


CDRH Compliant Yes
Operating Voltage (VAC) 100 to 240
Frequency (Hz) 50 to 60
Power Consumption (W) 500
Ambient Temperature (°C)
Operating 10 to 40
Non-Operating -10 to 60
Relative Humidity8 (%) 5 to 95
CE Marking IEC 61010-1/EN 61010-1
Dimensions (L…

Genesis-MX-Series-607-639-MTM-OEM

Genesis-MX-Series-607-639-MTM-OEM

…Diode Current (A) <32 <32, <35
Diode Voltage (V) 1.5 to 2.2
Cooling Requirements5 Active cooling required
Case Temperature (°C) 20 ±2
Humidity Non-condensing
Dimensions (L x W x H)
Laser Head 256 x 49 x 71 mm (10.07 x 1.93 x 2.76 in.)
Weight
Laser…

COHR DIAMOND C-20 DS 0817 1.pdf

COHR DIAMOND C-20 DS 0817 1.pdf

…maintenance air-cooled design with rugged reliability · Flexible, extremely compact and easy to install · Economical, high quality laser processing on a wide range of materials · Optimized performance at multiple wavelengths (9.3 µm or 10.6 µm) APPLICATIONS · Marking · Engraving Diamond C-20 Series

Powered by Site Search powered by SLI Systems

Please Read Before Continuing

Risk factors: Except for the historical information contained here, many of the matters discussed in this Web site are forward-looking statements, based on expectations at the time they were made, that involve risks and uncertainties that could cause our results to differ materially from those expressed or implied by such statements. These risks are detailed in the “Factors That May Affect Future Results” section of our latest 10-K or 10-Q filing. Coherent assumes no obligation to update these forward-looking statements.


I have read the terms and conditions